Features Service, Current, System, Status

6. INFORMATION menu

	Function	Description
	FAQ-Image
	and
	Installation	Displays possible solutions to problems you may encounter.

	FAQ-
	FAQ-
	Features and
	Service

		Source
		Shows the current signal source.
		Picture Mode
		Shows the selected mode in the PICTURE menu.
	Current	Resolution
	Current	Shows the native resolution of the input signal.
	System	Shows the native resolution of the input signal.
	System	Color System
	Status	Color System
	Status	Shows input system format: NTSC, PAL, SECAM, YUV, or RGB.
		Shows input system format: NTSC, PAL, SECAM, YUV, or RGB.
		Equivalent Lamp Hour
		Displays the number of hours the lamp has been used.
		Firmware Version
		Shows the firmware version of your projector.

Operation 61

Page 61

Image 61

BenQ MX761 user manual Features Service, Current, System, Status

Contents

MX760/MX761 Digital Projector Welcome Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Important safety instructions Safety Instructions Locations with an ambient temperature Locations near fire alarmsLocations where the altitudes are higher Confined. Allow at least 50 cm clearance It from the power supplys power outlet InstalledServiced Do not step on the projector or place Introduction Projector featuresIntroduction Shipping contents Rear/lower side Projector exterior view Focus ring Power indicator lightZoom ring Left Test Remote controlAuto Keystone/Arrow buttons / Up Down Mute Operating the Laser pointerMIC/VOL + Numeric buttons Replacing the remote control batteries Remote control effective rangeApprox.+15º Choosing a location Positioning your projectorFront Table Front Ceiling Obtaining a preferred projected image size Projection dimensions Shifting the projection lens When the projector position is fixed Video cable Hdmi cable Connection Connection Connecting audio Connecting video source devicesTerminal name Terminal appearance Best About the microphone input Playing sound through the projectorDevice Page Starting up the projector OperationOperation Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Correcting keystone Following example describes how to set the OSD language Using the menusUse / to highlight the System Setup Basic menu Utilizing the password function Using a security cable lockSetting a password Highlight Change Security Settings and press MODE/ENTER Entering the password recall procedure If you forget the passwordChanging the password Write down the number and turn off your projector Disabling the password function Changing Color Space Switching input signal Selecting the aspect ratio Magnifying and searching for details Adjustments Projectors native resolution in its Displayed in the centerAbout the aspect ratio Screen with a 169 aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes Every adjustment made will reflect to Press To highlight Saturation and adjust its3D Color Management Range at 0, only pure red in the projected To cancel the timer, perform the following steps Setting the presentation timerCount Up Increases from 0 to the preset time Count Down Selection Description Remote paging operations Utilizing FAQ functionFreezing the image Hiding the image Using the remote control To activate the High Altitude ModeLocking control keys Operating in a high altitude environment Adjusting the sound level Adjusting the soundAdjusting the microphone volume Turning off the Power On/Off Ring Tone Cable connection Controlling the projector through a LAN environmentIf you are in a Dhcp environment If you are in a non-DHCP environment Highlight Wireless LAN and press MODE/ENTER Wireless connection Controlling the projector remotely through a web browser Page Page Iii Operation Page Operation Page Using Q Presenter Downloading and installing Q PresenterDisplaying images through Q Presenter Operation Operation Presenting from a USB Reader Once the cooling process finishes, a Power Off Ring Direct power offShutting down the projector Menu system Menu operationMain menu Sub-menu Options Basic Advanced Advanced Network Description of each menu Temperature Picture ModeManagement Save Settings Display menu Picture menu Function Description Teaching Timer System Setup Basic menu Function Description Quick AutoSettings Search Panel Key Settings Security DescriptionBackground Lock Reset All System Setup Advanced menu Function DescriptionBaud Rate Test Pattern Current Features ServiceSystem Status Care of the projector Maintenance Setting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hour Status Message Timing of replacing the lamp Replacing the lamp Tighten the screw that secures the lamp Resetting the lamp timer Connect the power and restart the projectorTighten the screw that secures the lamp cover Light Status & Description Power events IndicatorsLamp events Thermal events Troubleshooting Projector specifications Specifications Mm W x 128 mm H x 252 mm D DimensionsCeiling Mount screw M4 x 8 Max L = 8 mm Unit mm Supported timing for PC input Timing chart Supported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputTiming Horizontal Limited warranty Warranty and Copyright informationCopyright Disclaimer FCC statement for United States users Regulation statementsEEC statement for European users Weee directive

FAQ-

Features and

Service

Current

System

Status

Operation 61