Manuals / BenQ / Computer Equipment / Projector

BenQ MX764 Information menu Function Description, Network, Reset All, Current, System, Status

Models: MX764

1 79

Download 79 pages 28 Kb

Page 65

5. SYSTEM SETUP: Advanced menu

6. INFORMATION menu

	Function	Description
		Wired LAN
		Wireless LAN
		Remote Desktop
		Projection Log In Code
		Broadcasting
	Network	See "Using the broadcasting function" on page 52 for details.
	Network	AMX Device Discovery
	Settings	AMX Device Discovery
	Settings	When AMX Device Discovery is On, the projector can be detected by

		AMX controller.
		Mac Address
		Displays the mac address for this projector.
		The System limitation of 1:1 audio is Intel Pentium 4, 3.0G CPU, 1G
		RAM.
		Returns all settings to the factory preset values.
	Reset All	The following settings will still remain: Phase, H. Size, User 1, User
	Settings	2, Color Space Conversion, Language, Projector Position, High
		Altitude Mode, Security Settings, DHCP, SSID, Remote Desktop and
		Baud Rate.
		Source
		Shows the current signal source.
		Picture Mode
		Shows the selected mode in the PICTURE menu.
	Current	Resolution
	Current	Shows the native resolution of the input signal.
	System	Color System
	Status	Shows input system format: NTSC, PAL, SECAM, YUV, or RGB.
		Equivalent Lamp Hour
		Displays the number of hours the lamp has been used.
		Firmware Version
		Shows the firmware version of your projector.

Operation 65

Image 65

BenQ MX764 user manual Information menu Function Description, Network, Reset All, Current, System, Status

Contents

MX763/MX764 Digital Projector WelcomeTable of contents Refer servicing to qualified service personnel Important safety instructionsSafety Instructions Safety Instructions Confined. Allow at least 50 cm clearance Ceiling mounting the projector Introduction Projector featuresShipping contents Rear/lower side Projector exterior viewFront/upper side Controls and functions 22 12. Network Remote controlAuto Keystone/Arrow buttons / Up DownOperating the Laser pointer VOLUME+/VOLUME- Adjusts the sound level MuteMIC/VOL + Numeric buttonsReplacing the remote control batteries Remote control effective rangeChoosing a location Positioning your projectorFront Table Front CeilingObtaining a preferred projected image size Projection dimensionsShifting the projection lens When the projector position is fixedConnection ConnectionConnecting audio Connecting video source devicesAbout the microphone input Audio Settings Microphone Volume menuPlaying sound through the projector Connection Starting up the projector OperationAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Use / to highlight the System Setup Basic menu Using the menusUtilizing the password function Using a security cable lockSetting a password Securing the projectorChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Selecting a picture mode Using Wall ColorSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes RED Top-Left Bottom-Left Top-Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps Hiding the image Remote paging operationsFreezing the image Using the remote control To activate the High Altitude ModeLocking control keys Operating in a high altitude environmentAdjusting the sound level Adjusting the soundAdjusting the microphone volume Turning off the Power On/Off Ring ToneCable connection Controlling the projector through a LAN environmentIf you are in a Dhcp environment If you are in a non-DHCP environmentHighlight Wireless LAN and press MODE/ENTER Wireless connectionSetting the Infrastructure mode Operation Controlling the projector remotely through a web browser Operation Operation Iii Press Exit to go back to the remote network operation Operation Operation Using the web control lock Displaying images through QPresenter Downloading and installing QPresenterUsing QPresenter Operation Operation Using the Projection Login Code Using the USB cable to display computer contentUsing the broadcasting function Presenting from a USB Reader Shutting down the projector Using the USB CameraDirect power off Menu system Menu operationMain menu Sub-menu Options BasicAdvanced System Setup BasicDhcp Main menu Sub-menu Options System Setup AdvancedDescription of each menu Temperature Picture ModeManagement Save Settings Display menu Picture menu Function Description TeachingFunction Description Quick Auto TimerSearch Color SpaceOperation SettingsRemote Advanced menu Security Settings DescriptionReceiver Panel KeyBaud Rate System Setup Advanced menu Function DescriptionTest Pattern ClosedInformation menu Function Description Reset AllNetwork CurrentCare of the projector MaintenanceLamp information Setting Lamp Mode as EconomicGetting to know the lamp hour Extending lamp lifeStatus Message Timing of replacing the lampReplacing the lamp Ensure the handle is fully laid flat and locked in place Tighten the screws that secure the lamp cover Resetting the lamp timerLight Status & Description Power events IndicatorsLamp events Thermal eventsCause Remedy TroubleshootingProjector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartSupported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputLimited warranty Warranty and Copyright informationCopyright Disclaimer