Operation | BenQ MX764 instruction

•The QPresenter only accepts up to 8 characters consisting of English capitalized letters and digits 0-9 for the name, full 6 digits consisting of 1 to 4 for the password.

•To change the QPresenter interface language, click the down arrow to reveal a drop-down list and select a desired language. Click Apply.

•To allow notification messages to appear, click Yes. Click Apply.

•To display your computer screen on multiple projectors, click Activate 1:N Display. Click Apply. It can display up to 8 projectors at the same time.

4.The Advanced Settings page allows you to configure QPresenter.

•To display still pictures, click the down arrow to reveal a drop-down list and select Graphic. Click Apply. To display video clips, click the down arrow to reveal a drop-down list and select Video. Click Apply.

Graphic mode: worse image quality but faster transmission speed.

Video mode: better image quality but slower transmission speed.

However, the actual transmission speed was determined by the network traffic at that time.

•To adjust the capture rate, move the slide bar. The network bandwidth may also affect the performance.

•To launch QPresenter when your computer operating system is started, click Yes for Boot and launch. Click Apply.

•To link to the Projector Network Display System web page, click Link.

5.Disconnect

To disconnect from the projector(s), click the Disconnect icon.

• Be sure to turn off other virtual network control programs before using QPresenter.

•Firewall in the PC must be switched off to allow QPresenter and USB Display to work.

•Wireless keyboard mouse combo is not supported by Pixelworks currently.

Operation 51

Image 51

BenQ MX764 user manual Operation

Contents

MX763/MX764 Digital Projector Welcome Table of contents Important safety instructions Safety InstructionsRefer servicing to qualified service personnel Safety Instructions Confined. Allow at least 50 cm clearance Ceiling mounting the projector Introduction Projector features Shipping contents Projector exterior view Front/upper sideRear/lower side Controls and functions Keystone/Arrow buttons / Up Down Remote control22 12. Network Auto Numeric buttons VOLUME+/VOLUME- Adjusts the sound level MuteOperating the Laser pointer MIC/VOL + Replacing the remote control batteries Remote control effective range Front Ceiling Positioning your projectorChoosing a location Front Table Obtaining a preferred projected image size Projection dimensions Shifting the projection lens When the projector position is fixed Connection Connection Connecting audio Connecting video source devices Audio Settings Microphone Volume menu Playing sound through the projectorAbout the microphone input Connection Starting up the projector Operation Fine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the image Correcting keystone Use / to highlight the System Setup Basic menu Using the menus Securing the projector Using a security cable lockUtilizing the password function Setting a password If you forget the password Entering the password recall procedureChanging the password Disabling the password function Changing Color Space Switching input signal Selecting the aspect ratio Magnifying and searching for details About the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 mode Fine-tuning the image quality in user modes RED Setting the presentation timer To cancel the timer, perform the following stepsTop-Left Bottom-Left Top-Right Bottom-Right Remote paging operations Freezing the imageHiding the image Operating in a high altitude environment To activate the High Altitude ModeUsing the remote control Locking control keys Turning off the Power On/Off Ring Tone Adjusting the soundAdjusting the sound level Adjusting the microphone volume If you are in a non-DHCP environment Controlling the projector through a LAN environmentCable connection If you are in a Dhcp environment Wireless connection Setting the Infrastructure modeHighlight Wireless LAN and press MODE/ENTER Operation Controlling the projector remotely through a web browser Operation Operation Iii Press Exit to go back to the remote network operation Operation Operation Using the web control lock Downloading and installing QPresenter Using QPresenterDisplaying images through QPresenter Operation Operation Using the USB cable to display computer content Using the broadcasting functionUsing the Projection Login Code Presenting from a USB Reader Shutting down the projector Using the USB Camera Direct power off Basic Menu operationMenu system Main menu Sub-menu Options Advanced System Setup Basic Dhcp Main menu Sub-menu Options System Setup Advanced Description of each menu Display menu Picture menu Function Description Teaching Picture ModeTemperature Management Save Settings Color Space TimerFunction Description Quick Auto Search Operation Settings Panel Key Advanced menu Security Settings DescriptionRemote Receiver Closed System Setup Advanced menu Function DescriptionBaud Rate Test Pattern Current Reset AllInformation menu Function Description Network Care of the projector Maintenance Extending lamp life Setting Lamp Mode as EconomicLamp information Getting to know the lamp hour Status Message Timing of replacing the lamp Replacing the lamp Ensure the handle is fully laid flat and locked in place Tighten the screws that secure the lamp cover Resetting the lamp timer Thermal events IndicatorsLight Status & Description Power events Lamp events Cause Remedy Troubleshooting Projector specifications Specifications Ceiling mount installation Dimensions Supported timing for PC input Timing chart Supported timing for Hdmi Hdcp input Supported timing for Video and S-Video inputs Supported timing for Component-YPbPrinput Disclaimer Warranty and Copyright informationLimited warranty Copyright