System Setup Advanced menu Function Description | BenQ MX764

5. SYSTEM SETUP: Advanced menu

	Function	Description
		Selects a baud rate that is identical with your computer’s so that you can
	Baud Rate	connect the projector using a suitable RS-232 cable and update or
	Baud Rate	download the projector’s firmware. This function is intended for

		qualified service personnel.

	Test Pattern	Selecting On enables the function and the projector displays the grid test
	Test Pattern	pattern. It helps you adjust the image size and focus and check that the
		projected image is free from distortion.

		Closed Caption Enable
		Activates the function by selecting On when the selected input signal
		carries closed captions.
	Closed	• Captions: An on-screen display of the dialogue, narration, and
	Closed	sound effects of TV programs and videos that are closed captioned
	Caption	(usually marked as "CC" in TV listings).
		Caption Version
		Selects a preferred closed captioning mode. To view captions, select
		CC1, CC2, CC3, or CC4 (CC1 displays captions in the primary language
		in your area).

		Network
		Selecting On enables the function. The projector is able to provide the
		network function when it is in standby mode.
		Microphone
		Selecting On enables the function. The projector can output the
		microphone signal when it is in standby mode and all the necessary
		equipment is correctly connected. See "Playing sound through the
		projector" on page 19 for details.
	Standby	Monitor Out
	Standby	Selecting On enables the function. The projector can output a VGA
	Settings
	Settings	signal when it is in standby mode and the COMPUTER 1 jack is
		correctly connected to devices. See "Connection" on page 17 for how to
		make the connection.
		Audio Pass Through
		Selecting On enables the function. The projector can play sound when it
		is in standby mode. Connect the correct signal cable and connect the
		audio cable to the AUDIO IN jack. See "Connection" on page 17 for how
		to make the connection.
		Enabling this function slightly increases the standby power
		consumption.

64 Operation

Image 64

BenQ MX764 user manual System Setup Advanced menu Function Description, Baud Rate, Test Pattern, Closed, Caption, Standby

Contents

Welcome MX763/MX764 Digital Projector Table of contents Safety Instructions Important safety instructionsRefer servicing to qualified service personnel Safety Instructions Confined. Allow at least 50 cm clearance Ceiling mounting the projector Projector features Introduction Shipping contents Front/upper side Projector exterior viewRear/lower side Controls and functions Remote control 22 12. NetworkAuto Keystone/Arrow buttons / Up Down VOLUME+/VOLUME- Adjusts the sound level Mute Operating the Laser pointerMIC/VOL + Numeric buttons Remote control effective range Replacing the remote control batteries Positioning your projector Choosing a locationFront Table Front Ceiling Projection dimensions Obtaining a preferred projected image size When the projector position is fixed Shifting the projection lens Connection Connection Connecting video source devices Connecting audio Playing sound through the projector Audio Settings Microphone Volume menuAbout the microphone input Connection Operation Starting up the projector Adjusting the projected image Adjusting the projection angleAuto-adjusting the image Fine-tuning the image size and clarity Correcting keystone Using the menus Use / to highlight the System Setup Basic menu Using a security cable lock Utilizing the password functionSetting a password Securing the projector Entering the password recall procedure If you forget the passwordChanging the password Disabling the password function Switching input signal Changing Color Space Magnifying and searching for details Selecting the aspect ratio About the aspect ratio Using Wall Color Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menu Fine-tuning the image quality in user modes RED To cancel the timer, perform the following steps Setting the presentation timerTop-Left Bottom-Left Top-Right Bottom-Right Freezing the image Remote paging operationsHiding the image To activate the High Altitude Mode Using the remote controlLocking control keys Operating in a high altitude environment Adjusting the sound Adjusting the sound levelAdjusting the microphone volume Turning off the Power On/Off Ring Tone Controlling the projector through a LAN environment Cable connectionIf you are in a Dhcp environment If you are in a non-DHCP environment Setting the Infrastructure mode Wireless connectionHighlight Wireless LAN and press MODE/ENTER Operation Controlling the projector remotely through a web browser Operation Operation Iii Press Exit to go back to the remote network operation Operation Operation Using the web control lock Using QPresenter Downloading and installing QPresenterDisplaying images through QPresenter Operation Operation Using the broadcasting function Using the USB cable to display computer contentUsing the Projection Login Code Presenting from a USB Reader Using the USB Camera Shutting down the projector Direct power off Menu operation Menu systemMain menu Sub-menu Options Basic System Setup Basic Advanced Main menu Sub-menu Options System Setup Advanced Dhcp Description of each menu Picture Mode TemperatureManagement Save Settings Display menu Picture menu Function Description Teaching Timer Function Description Quick AutoSearch Color Space Settings Operation Advanced menu Security Settings Description RemoteReceiver Panel Key System Setup Advanced menu Function Description Baud RateTest Pattern Closed Reset All Information menu Function DescriptionNetwork Current Maintenance Care of the projector Setting Lamp Mode as Economic Lamp informationGetting to know the lamp hour Extending lamp life Timing of replacing the lamp Status Message Replacing the lamp Ensure the handle is fully laid flat and locked in place Resetting the lamp timer Tighten the screws that secure the lamp cover Indicators Light Status & Description Power eventsLamp events Thermal events Troubleshooting Cause Remedy Specifications Projector specifications Dimensions Ceiling mount installation Timing chart Supported timing for PC input Supported timing for Hdmi Hdcp input Supported timing for Component-YPbPrinput Supported timing for Video and S-Video inputs Warranty and Copyright information Limited warrantyCopyright Disclaimer