OPTION Menu
With the OPTION menu, the items shown in the table below can be performed. Perform each operation in accordance with the instructions in the table below.
MENU |
|
|
|
MAIN | VOLUME | 16 |
|
SPEAKER | TURN ON | ||
IR REMOTE | 1: 2: | 3: | |
INPUT | IR REMOTE ID | ALL |
|
AUTO | LAMP TIME | 1234 h |
|
SCREEN | FILTER TIME | 4321 h |
|
OPTION | SERVICE |
|
|
NETWORK | PIN LOCK | TURN ON | |
: SELECT |
|
|
|
Item |
|
| Description |
|
|
| |
VOLUME | Adjust the volume using the 5 / 6 buttons. : | ||
High |
| Low | |
|
| ||
Select the TURN ON or the TURN OFF using the 5 / 6 buttons. :
SPEAKER | TURN ON |
| TURN OFF |
|
When the TURN ON is selected, the
Select a remote sensor using the 5 / 6 button (1), then switch it using the ENTER button (2). :
IR REMOTE (1) 1 : FRONT |
| 2 : TOP |
| 3 : REAR (2) |
| (Off) |
|
|
| (On) |
|
|
|
|
|
| |||||
|
|
|
|
memo A sensor cannot be turned off when the other two are off. Always at least one sensor is on.
Select a number as an ID number for remote control using the 5 /
6buttons. :
| ALL |
| 1 |
| 2 |
|
| 3 |
| |||
|
|
|
|
| ||||||||
IR REMOTE ID | The projector is controlled by the remote control whose ID | |||||||||||
CHANGE switch is set into the position of the same number as this | ||||||||||||
| number. When the ALL is selected, the projector is controlled by a | |||||||||||
| remote control irrespective of the position of the ID CHANGE | |||||||||||
| switch. |
|
|
|
|
|
|
|
|
| ||
| memo Please refer to the section Using The Remote ID Feature. |
| ||||||||||
| Pressing the RESET button for about 3 seconds displays the LAMP | |||||||||||
| TIME menu. Select the RESET using 5 button to reset the timer. : | |||||||||||
| RESET |
|
|
| CANCEL |
|
| |||||
|
|
|
|
|
| |||||||
LAMP TIME | Selecting the RESET resets the count of the lamp timer to 0. | |||||||||||
memo Perform this function only when you have replaced the lamp. | ||||||||||||
| The lamp timer counts the used time of the current lamp, to display | |||||||||||
| the messages about the lamp. Incorrect performing causes incorrect | |||||||||||
| operation of the messages. | |||||||||||
| memo About replacing the lamp, please refer to the section Lamp. | |||||||||||
|
|
|
|
|
|
|
|
| ||||
| Pressing the RESET button for about 3 seconds displays the FILTER | |||||||||||
| TIME menu. |
|
|
|
|
|
| |||||
| Select the RESET using 5 button to reset the timer. : | |||||||||||
| RESET |
|
|
| CANCEL |
|
| |||||
|
|
|
|
|
| |||||||
| Selecting the RESET resets the count of the lamp timer to 0. | |||||||||||
FILTER TIME | memo Perform this function only when you have cleaned or | |||||||||||
replaced the air filter. The filter timer counts the used time of the air | ||||||||||||
| ||||||||||||
| filter after cleaning or replacement, to display the messages about the | |||||||||||
| air filter. Incorrect performing causes incorrect operation of the | |||||||||||
| messages. |
|
|
|
|
|
|
|
|
| ||
| memo About caring for the air filter, please refer to the section Air | |||||||||||
| Filter. |
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| (This table is continued to the following page.) | ||||
32 Multifunctional Settings
