8
NotICe: This unit will kill 99.9% of bacteria and germs when used in accordance with
this manual and with the micro fiber pad fitted and a continuous run time of 90 seconds

HINtS for oPtImum uSe

geNeral uSe
CautIoN: Never use the steam mop without first attaching a cleaning pad.
WarNINg: It is important to monitor the water level in the water tank. To refill the
water tank and continue to sanitize/clean, see Filling the Water Tank section.
CautIoN:
Never leave the steam mop in one spot on any surface for any period of
time. Always place the steam mop on the resting mat (7) with the handle tube in the upright
position when stationary and make sure the steam mop is turned off when not in use.
• Alwaysvacuumorsweepthefloorbeforeusingthesteammop.
• The easiest way to use the steam mop is to tilt the handle to a 45˚ angle and clean
slowly, covering a small area at a time.
• Donotusechemicalcleanerswithyoursteammop. To remove stubborn stains
from vinyl or linoleum floors, you can pre-treat them with a mild detergent and some
water before using the steam mop.
Steam CleaNINg
• Place a cleaning pad (6) on the floor with the ‘hook & loop’ side facing up.
•
Raise the steam mop off the resting mat (7) and lightly press it down onto the cleaning pad.
• Place the steam mop on the resting mat.
• Plug the steam mop electric cord into the outlet.
• Press the ON/OFF button (1). It takes approximately 15 seconds for the steam mop to heat up.
• Press the SmartSelecttm button (2) until the required setting is reached.
• Pulling the handle tube (4) back will activate the steam pump. After a few seconds
steam will start to come out of the steam head.
NotICe: If the system has been run dry it may take up to 30 seconds to prime the
system on first use.
• It takes a few seconds for steam to enter the cleaning pad. The steam mop will now
glide easily over the surface to be sanitized/cleaned.
•
Push and pull the steam mop slowly across the floor to thoroughly steam clean each section.
NotICe: During use you may turn off the steam pump by returning the handle to
the upright position, this convenient feature will allow you to place the steam mop on
the resting mat for a short time so that you may move items of furniture, then continue
cleaning without the need to switch the appliance off.
CarPet refreSHINg
WarNINg:
It is important to monitor the water level in the water tank. To refill the
water tank and continue to sanitize/ clean, return the handle tube (4) to the upright position
and turn the steam mop ‘OFF’. Unplug the unit from the electrical wall outlet, remove and refill
the water tank (3).
CautIoN: Never leave the steam mop in one spot on any surface for any period
of time. Always place the steam mop on the resting mat (7) with the handle tube in the upright
position when stationary and make sure the steam mop is turned off when not in use.
• Place the carpet glider (8) on the floor.
• Lightly press the steam mop with attached cleaning pad down onto the carpet glider
until it clicks into place.
• Place the steam mop on the resting mat.
• Plug the steam mop electric cord into the outlet.
•
Press the ON/OFF button (1). It takes approximately 15 seconds for the steam mop to heat up.
• Press the SmartSelecttm button (2) to the Wood/Laminate setting.
• Pulling the handle tube back will activate the steam pump. After a few seconds steam
will start to come out of the steam head.
•
Push and pull the steam mop slowly across the carpet to thoroughly refresh each section.
NotICe: During use you may turn off the steam pump by returning the handle tube to the
upright position, this convenient feature will allow you to place the steam mop on the resting
mat so that you may move items of furniture with out the need to switch the appliance off.