Black & Decker BDPS200 Warranty, Troubleshooting, Problem Possible Cause Possible Solution

Full Two-Year Home Use Warranty			WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The
defective product will be replaced or repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased
(provided that the store is a participating retailer). Returns should be made within the time period of the retailerʼs policy
for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer
for their specific return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for
repair or replacement at our option. Proof of purchase may be required.Black & Decker owned and authorized Service
Centers are listed under "Tools-Electric" in the yellow pages of the phone directory.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other
rights which vary from state to state or province to province. Should you have any questions, contact the manager of
your nearest Black & Decker Service Center. This product is not intended for commercial use.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America,
check country specific warranty information contained in the packaging, call the local company or see the website for
warranty information.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call
1-800-544-6986for a free replacement.		TROUBLESHOOTING
Problem	Possible Cause			Possible Solution
• Material runs or drips	• Spraying too much material.			• Reduce air flow by turning flow control
	• Spraying too slowly.			knob.
				• Increase speed of application.
	• Spraying too close.			• Increase distance from surface.
• Too much over spray.	• Viscosity too thin.			• Check dilution recommendation.
	• Sprayer too far from surface.			• Reduce distance to surface.
	• Too much material being sprayed.			• Reduce flow by turning flow control
• Little or no materialbeing released.	• Spray nozzle/tip clogged.			knob clockwise.
				• Clean nozzles.
	• Pickup tube loose or clogged.			• Check tube.
	• Flow control knob setting too low.			• Increase flow control setting.
• Materialbeing sprayedis splattering.	• Material too thick.			• Check viscosity recommendation.
	• Viscosity of material is too low.			• Thin materialper manufacturer
• Sprayer pulsates.	recommendation.			• Refill canister.
	• Material in canister almost empty.
• Liquid comes out side of canister.	• Lid not on square or tight enough.			• Remove lid and reattach squarely and
	• Paint on threads of canister and lid.			evenly, then tighten cap securely.
				• Clean threads on top and sides of
• Motor operates properly but does	• Plugged or worn atomizer valve.			canister and lid.
				• Clean or replace as needed.
not spray.	• Atomizer valve missing.			• Put in atomizer valve.
	• Material too thick.			• Thin material.
	• Plugged spray tip.			• Clean tip.
	• Intake filter plugged.			• Clean intake filter.
	• Control knob needs adjusting.			• Adjust knob.
• Cannot reassemble unit.	• Worn piston.			• Clean and oil or replace
	• Skipped an assembly step.			• Insertspringand pistoninto the housing
				prior to reassembling.

• Press and hold the release button while reassembling.

For assistance with your product, visit our website www.blackanddecker.com for the location of the service center nearest you or call the BLACK & DECKER help line at 1-800-544-6986.

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

See ‘Tools-Elec-

tric’

– Yellow Pages –

for Service &

14Sales