PW1600 |
|
|
| F | |
|
| D |
|
|
|
K |
| M |
|
| F2 |
| P | N |
| L |
|
|
|
|
| ||
|
|
| O | F1 | |
|
| C |
| ||
|
|
|
|
| |
I | IO |
|
|
| H |
|
|
|
|
| |
|
| B | E1 | E | J |
|
| Q |
|
|
|
PW1750 |
|
|
| F | |
|
| D |
|
|
|
K |
|
|
|
| F2 |
P | M |
| O |
| |
| N |
| L | F1 | |
|
| C |
| ||
I |
|
|
|
| |
O |
|
|
|
| |
I |
|
|
|
| |
|
|
|
|
| |
|
| G |
|
| H |
|
|
|
|
| |
| Q | B |
|
|
|
| A | E1 | E | J | |
|
|
UNIT ASSEMBLY
PW1600 ASSEMBLY:
Tools Required:
Philips screwdriver
Adjustable wrench
Hardware Bag Contents:
-2 pcs. flat washers
-2 pcs. hex locking nuts
-6 pcs. 5/8” screws
Wheel Assembly - PW1600
Remove the 2 protective plastic end caps from axle and discard. Place wheel (E), flat washer, and hex locking nut over axle end as shown with smooth face of wheel having circular holes only facing outwards (side of wheel with raised spokes faces inwards toward pressure washer body). Using a wrench, tighten nut securely. Align wheel cap (E1) over wheel face as shown and press center of wheel cap until it snaps securely to wheel.
1 | PW1600 |
Handle Assembly - PW1600
1.) With rectangular steel tube (N) ends pointing upwards as labeled, push tubes down firmly into rectangular holes in black top housing (P) until they hit bottom.
2.) Drive one 5/8” screw through the hole in each side of the orange housing (Q) as shown and into the tapped hole of the tube until tight.
2PW1600
“UP” | 4 | |
Label | ||
| ||
| 1 | |
| 3 | |
2 |
|
Upper Cord Wrap Hook Assembly - PW1600
Insert cord wrap top hook (M) into the rear slot in handle (K), pushing down firmly until it stops. Drive two 1 1/2” self tapping screws included in cord hook bag through handle holes into cord wrap hook as shown until tight. DO NOT over tighten.
3PW1600
PW1750 ASSEMBLY:
Tools Required:
A.High pressure water outlet (OUTLET)
B.Pump Quick Connector
C.High pressure turbo wand
D.Adjustable fan wand
E.Wheels
E1. Wheel Cap
F.Gun
F1. High pressure hose connector
F2. Gun safety catch
G.Power supply cord with GFCI
H.Hardware bag
4
I.On/off switch
J.Garden hose Quick Connector
K.Handle
L.Removable detergent tank with cap
M.Cord wrap top hook
N.Steel Support tubes
O.Nozzle Cleaning tool
P.Black top housing
Q.Orange main housing
3.) Next drive one 5/8” screw through each hole in the upper back side of the black top housing (P) as shown into the tapped hole of the tube until tight.
4.) You are now ready to align the rectangular holes in bottom of handle (K) over the tubes, pushing the handle down until it’s bottom edge slides into black housing (P) fully. Drive one 5/8” screw through each hole in the back of the handle
(K)as shown into the tubes until tight to complete handle assembly.
5
Philips screwdriver
Adjustable wrench
Hardware Bag Contents:
-2 pcs. flat washers
-2 pcs. hex locking nuts
Wheel Assembly - PW1750
Remove the 2 protective plastic end caps from axle and discard. Place wheel (E) with 5 raised square bumps facing outwards as shown below over threaded axle end, followed by flat washer, and hex locking nut. Using wrench, tighten nut securely. Align 5 square knotches in wheel cap (E1) to raised