Bosch Appliances Nexxt DLX Dimensions, Installation Area, Removing, Floor, transport Bolts, Wmz

If the washing machine is to be installed on a weak wood floor consider the following:

Useful

tools

q

Soft floor

surfaces,

such

as

The

following

tools

are

helpful:

carpets or surfaces with foam

-

Flat

head

screwdriver.

backing,

are

not suitable. If

possible,

place

the

washing

-

Closed

wrench

(1/2"/13mm).

machine

in

a

corner of

the

-

Bubble

level.

room.

Dimensions

q

Screw

a

water

resistant

wooden board (at least 3/4"

thick)

to

the floor.

q

Secure the

feet of

the

washing

-

Covers to be placed over the

machine

with holding brackets.

holes

for

the

transport bolts

Order the holding brackets (set)

(after

removing

them).

from

Bosch

Customer

Service

(WMZ

2200).

-

Clamp

for

drain

hose.

Units

are

not

designed

to

be

-

Wrench for

levelling.

q

-

Elbow for attaching the drain

stacked.

hose,

e.g.

to

a

sink.

q

Units

are

not

designed

for

Depending on the type of

under

counter

installation

connection, the

following

may

also

Pedestal

Mounting

be

required:

If

mounting the

washer

on

the

Bosch pedestal

(accessory

-

Y@connector

(can

be

obtained

no. WTZ1295)

follow the

instruc@

from any

hardware store)

in

tions supplied with

the

pedestal.

a = 27.0 inches (686 mm)

case there is only a cold water

i

connection

available.

b

=

30.7

inches (780

mm)

Install

pedestal

prior

to

Any

residual

moisture inside the

c = 37.0 inches (940 mm)

removing

transport

bolts.

d = 16.0 inches (407 mm)

Closet

drum is due

to

the

final

testing

Door

opening

angle

180°

If installing the washer in a closet,

which every

washing

machine

Approx.

weight

= 220

lbs

(100 kg)observe the

minimum

distances

undergoes

before

leaving

the

according to the following table:

factory.

Installation

area

Minimum

Installation Clearances

On

the rear

of

the

appliance:

Closet

d WARNING

d

Sides

1/4"

(6

mm)

Top

12"

(3O5

mm)

Never ground the washer to

Rear

2.5"

(64

mm)

plastic

plumbing lines,

gas

lines

Front

1/4"

(6

mm)

or

hot

water pipes.

This

appliance

must

be

installed Ventilation:

on a solid floor and

well

Top: 48

sq.

in

(310

sq. cm),

leveled

due to the higher spins speeds

Bottom: 24 sq.

in

(155

sq.

cm)

available.

If

installing

the

Removing

the

machine on a wood floor over a

basement or on a second

floor, transport

bolts

the

floor

may

need

to

be

CAUTION

reinforced.

Sound,

vibration,

and

All

4 transport

bolts

must

be

re@

risk

of

•walking"

will

be affected

-

Power

cord

with

plug.

depending

on

the

structure

and

moved before using the ap@

pliance for

the

first time

and

must

stability

of the

floor

surface

C = cold

water

connection

be retained for any future trans@

where

it

is

installed.

H = hot

water

connection

port (e.g. when

moving).

7