BM 2610028021
Functional Description and Specifications
Assembly
!WARNING Disconnect the plug from the power source before making any assembly, adjustments or changing accessories. Such preventive safety
measures reduce the risk of starting the tool accidentally.
Planer
“LOCK-OFF”
BUTTON
FIG. 1
CHIP | DEPTH | |
ADJUSTMENT | ||
EXHAUST | ||
KNOB | ||
PORT | ||
| ||
RABBETING | TRIGGER SWITCH | |
| ||
DEPTH STOP | PARK REST STAND | |
(OPTIONAL) | ||
|
BLADE WRENCH STORAGE
WING | DRIVE BELT COVER |
| |
KNOB | SCREW |
|
CHIP ExTRACTION
The planer comes with two chip exhaust ports, which may be used with a chip bag (Fig.2) or a shop vacuum and vacuum connector (Fig.3) to keep your work environment cleaner. The chip bag or vacuum connector may be attached to either end of the exhaust port.
Moving the port selector lever to position 1 (towards front of tool) discharges chips to the left, while position 2 (towards rear of tool) discharges chips to the right. (Fig. 1)
The optional VAC002 adapter will connect the hood to
PLANER BLADES
• There are three types of blades that can be |
used with the Bosch 1594 planer; standard |
mini tungsten carbide blades, Bosch |
Woodrazor micrograin mini tungsten carbide |
blades (standard equipment with the Bosch |
FIG. 2
CHIP BAG | EXHAUST |
| PORTS |
FIG. 3
VACUUM
CONNECTOR (OPTIONAL)
ADJUSTABLE
FRONT SHOE
CHAMFER DEPTH
FENCE
| GUIDE | |
| BRACKET | |
| PIVOT | |
Note: Each unlabeled | FENCE | |
mark represents | ROUND | |
0.5 mm. | ||
KNOB | ||
|
PORT | GUIDE |
SELECTOR | BRACKET |
LEVER |
|
| STANDARD |
| GUIDE |
| FENCE |
| WING |
| KNOB |
WING |
|
KNOB |
|
DELUXE GUIDE FENCE
(OPTIONAL)
WIDTH SCALE
WING KNOB
1594 planer), and large HSS blades. |
• While the Bosch 1594 mini tungsten carbide |
blades are sharper and more durable than |
standard mini tungsten carbide blades, the |
assembly and adjustment of both of |
Woodrazor and standard tungsten carbide |
blades are the same. Henceforth, all |
references in this manual to “mini TC |
blades” refer to both Woodrazor blades and |
standard mini tungsten carbide blades. |
• To use large HSS blades with the 1594 it is |
necessary to purchase optional accessories. |
Wear protective gloves ! WARNING when changing planer
blades. Edges are sharp and may cause injury.
REMOVING MINI TUNGSTEN
CARBIDE BLADES
Mini TC planer blades have two cutting edges, and may be reversed when one of the cutting edges becomes dull or chipped. (Fig. 6)
Before any work on the machine itself, pull the power plug.
Always changes both blades at the same time. Otherwise, imbalance can cause vibration and reduce the useful service life of the tool. Use only blades designated for use with this model,
because other blades can cause vibration, decrease performance and may not clamp securely in blade holder. Do not attempt to sharpen or use
To remove the blades:
1. Rotate the blade drum until the clamping jaw |
is parallel to the planer shoe. |
2. Loosen the three clamp screws by about |
one revolution each. (It is not necessary to |
remove the clamping jaw.) (Fig.4) |
3. Slightly rotate the blade drum and use a |
piece of wood to push the blade sideways |
and out from under the clamping jaw. Make |
sure to keep your fingers away from the |
sharp edges of the blade. If the blade is |
gummed and difficult to remove, you may |
clean the blade and clamp with mineral |
spirits, lacquer thinner or alcohol. (Fig. 5) |
4. Rotate the blade drum 180° and repeat the |
procedure to remove the second blade. |
Model number | 1594 | Maximum Capacities |
| |
Voltage rating | 120 V 50 - 60Hz | Planing depth | 0 | - 3/32" (0 - 2.6mm) |
Amperage rating | 6.5 A | Rabbeting depth | 0 | - 5/16" (0 - 9mm) |
No load speed | n0 16,500/min | Planing width |