Repair
|
|
|
|
|
|
|
|
| 3. If the measurement is less than 1/2” or greater than 3/4”, | |||
! |
| WARNING |
| ! | ||||||||
|
|
| loosen the two | |||||||||
|
|
| brake cable (B) to the chain case bracket. | |||||||||
DO NOT attempt any adjustments, maintenance, service or | 4. Adjust the cable up or down using the | |||||||||||
repairs with the engine running. STOP engine. STOP blade. | ||||||||||||
| a distance of 1/2” to 3/4” between the end of the clutch/ | |||||||||||
Engage parking brake. Remove key. Remove spark plug |
| |||||||||||
| brake cable (adjustment shown in inset of Figure 39) | |||||||||||
wire from spark plug and secure away from plug. Engine |
| |||||||||||
| and the bottom of the housing. | |||||||||||
and components are HOT. Avoid serious burns, allow all |
| |||||||||||
5. After adjustment is complete, securely tighten the cable | ||||||||||||
parts to cool before working on machine. |
| |||||||||||
|
| |||||||||||
|
|
|
|
|
|
|
|
| 6. Retest the wheel brake. | |||
How To Adjust The Brake / Parking Brake | ||||||||||||
Test the wheel brake on a dry concrete surface. When |
|
|
| |||||||||
|
|
| ||||||||||
properly adjusted, the unit will stop within 5 feet from fastest |
|
|
| |||||||||
speed. If stopping distance is more than 5 feet, adjustment |
|
|
| |||||||||
is required. |
|
|
|
|
|
|
|
|
|
| ||
Manual Drive Models: |
|
|
| B |
| |||||||
1. Set the parking brake. Refer to “How To Set The Parking |
|
|
| |||||||||
| Brake”. |
|
|
|
|
|
|
|
|
|
| |
2. Measure the distance (A, Figure 39) between the end of |
|
|
| |||||||||
| the clutch/brake cable (B) and the bottom of the housing |
| A |
| ||||||||
| (C). The measurement should be no less than 1/2” and |
|
| |||||||||
| no greater than 3/4”. |
|
|
|
|
| ||||||
NOTE: The cotter pin and brake spring (D and E, Figure 39) |
|
|
| |||||||||
are noted for reference purposes only. |
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
| for |
|
|
| |
|
|
|
|
|
|
|
|
| Figure 40: Brake cable adjusting nuts | |||
|
|
|
|
|
|
|
| Hydro Drive Models: | ||||
|
|
|
|
|
| Not | Contact an authorized dealer for assistance. | |||||
|
|
|
|
|
|
|
|
| ||||
| C |
|
|
|
|
| How To Adjust Mower Blade Belt Tension | |||||
|
|
|
|
|
|
| 1. Remove the mower deck cover. Refer to “How To | |||||
|
|
|
|
|
|
|
| Remove The Deck Cover”. | ||||
| E |
|
|
|
|
| 2. With the unit off and the mower blade disengaged (refer | |||||
|
|
|
|
| C |
| to “How To Engage The Mower Blade”), measure the | |||||
|
|
|
|
|
|
|
|
| body of the blade engage spring (A, Figure 41). | |||
| B |
|
|
|
|
|
|
| 3. Engage the mower blade, and measure the extended | |||
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
| D |
| blade spring (B). It should measure 3/8” to 1/2” longer | ||
|
|
|
|
|
|
|
| |||||
| D |
|
|
|
|
| Reproductionthan the unextended spring measurement in Step 2. | |||||
| A |
|
|
| ||||||||
|
|
|
| |||||||||
|
|
|
|
|
| 4. If adjustment is needed, disengage the mower blade, | ||||||
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
| loosen the rear jam nut (C) securing the PTO cable | ||
|
|
|
|
|
|
|
|
|
| housing (D), and adjust the cable housing in or out using | ||
| Figure 39: Adjusting the brake cable |
|
| |||||||||
|
|
|
| the front jam nut (E). | ||||||||
5. Repeat Steps 3 and 4 until the desired measurement is reached. Make sure to tighten the rear jam nut when adjustment is complete.
NOTE: Check to be sure there is slack in the PTO cable (F) when the mower blade is disengaged. This is essen- tial for correct operation of the blade brake. If there is no slack, lessen the cable tension until slack is obtained.
6. Replace the deck cover.
32 | www.snapper.com |
