Briggs & Stratton 7800918-00 Repr, oduction, How To Push The Unit By Hand, Towing Implements

Models: 7800921-00 7800920-00 7800932-00 7800918-00

1 40
Download 40 pages 42.23 Kb
Page 20
Image 20
How To Push The Unit By Hand

Operation

 

 

 

 

 

 

 

How To Push The Unit By Hand

!

WARNING

 

 

!

 

 

Manual Drive Models:

 

The mulching cover must remain on the machine at all

 

 

times. Do not remove.

 

 

 

 

1.

Make sure the unit is parked on a flat, even surface.

 

 

 

 

2.

Make sure the transmission shift lever is in the

 

 

 

 

 

Neutral (N) position. Refer to “How To Engage the

2. Raise the mulching cover. Replace the washer and

 

 

 

 

wing nut onto the retaining bolt in the deck, tightening

3.

Transmission”.

 

 

securely.

 

 

 

 

Release the parking brake, if set. Refer to “How To Set

3. Install the discharge deflector (A, Figure 20) to the

 

4.

The Parking Brake”.

 

 

mower deck, making sure that the slots (B) in the deflec-

The unit can now be pushed by hand. Be sure to set the

 

tor fit over the locking tabs (C) on the mulching cover

 

 

parking brake after the unit is moved to the desired loca-

 

hinge bracket.

 

 

 

 

 

 

tion.

 

4. Lower the mulching cover.

 

 

 

Hydro Drive Models:

 

5. To remove the discharge deflector:

 

 

 

 

 

• Raise the mulching cover.

 

 

 

1.

Make sure the unit is parked on a flat, even surface.

 

• Lift and remove the discharge deflector from the

2.

Release the parking brake, if set. Refer to “How To Set

 

 

mower deck.

 

 

 

 

3.

The Parking Brake”.

 

 

• Remove the wing nut and washer from the retaining

Move the transmission release lever (located behind

 

 

bolt in the deck.

 

 

 

 

 

 

the right rear tire) out and down into the locking slot (A,

 

• Lower the mulching cover, securing with the washer

4.

Figure 21) to disengage the transmission.

 

 

 

and wing nut. Tighten securely.

 

 

 

The unit can now be pushed by hand.

 

 

 

 

 

 

 

 

5.

After moving the unit to the desired location, move the

 

 

 

 

 

 

 

 

 

transmission release lever up and in (B) to engage the

 

 

 

 

Repr

 

 

 

 

 

 

oduction

 

 

 

 

 

 

 

 

 

 

transmission.

 

 

 

 

 

 

B

 

 

 

A

 

 

 

A

Not

for

 

 

 

B

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 19: Raising the mulching cover

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

C

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 21: Transmission release lever

 

 

Towing Implements

B

The maximum horizontal drawbar force allowed is 34 lbs

 

(150 N) *. The maximum vertical drawbar force is 20 lbs (90

 

N) *.

 

* Approximate

A

Figure 20: Installing the discharge deflector

20

www.snapper.com

Page 20
Image 20
Briggs & Stratton 7800918-00, 7800932-00 manual Repr, oduction, How To Push The Unit By Hand, Towing Implements, Operation