BSPP Generator

2.Slide axle through both axle mounting brackets on cradle frame, as shown in Figure 1.

3.Slide a wheel over the axle.

NOTE: Be sure to install both wheels with the air pressure valve on the outboard side.

4.Slide a flat washer over the axle and place the e-ring onto the groove in the axle.

5.Place one end of the needle nose pliers on the bottom of the axle and the other end of the pliers on top of the e-ring. Seat the e-ring by pressing the pliers closed.

6.Repeat step 3 through 5 to secure second wheel.

7.Remove the temporary blocks.

8.Attach the vibration mounts to the support leg with 1/4-20 x 3/4” capscrews and 1/4-20 lock nuts.

9.To aid support leg assembly, rest generator on cradle, engine end down. Remove the existing hardware from the left unit vibration mount with 13mm wrench. Use the same hardware to attach the support leg.

10.Attach the other side of the support leg with a M8 x 20 mm cap screw and M8 lock nut. Rest generator on wheels and support leg.

11.Attach handles to handle brackets on generator frame, as shown in Figure 1, with M8 x 45 mm capscrews, flat washers, nylon washers, and M8 lock nuts.

NOTE: Be sure to install the nylon washers between the handle brackets on the generator frame and the brackets on the handle assembly.

12.Loop handle pins to generator frame as shown in Figure 1. Raise handles and insert handle pins to move generator.

13.Check each fastener to ensure it is secure and the tires are inflated between 15-40 PSI.

CAUTION

Any attempt to crank or start the engine before it has been properly filled with the recommended oil will result in equipment failure.

Refer to engine manual for oil fill information.

Damage to equipment resulting from failure to follow this instruction will void warranty.

NOTE: Check oil often during engine break–in. Refer to engine owner’s manual for recommendations.

NOTE: The generator assembly rotates on a prelubricated and sealed ball bearing that requires no additional lubrication for the life of the bearing.

Add Fuel

NOTE: This gasoline engine is certified to operate on

gasoline. Exhaust Emission Control System: EM (Engine Modifications).

WARNING

Fuel and its vapors are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

WHEN ADDING FUEL

Turn generator OFF and let it cool at least 2 minutes before removing fuel cap. Loosen cap slowly to relieve pressure in tank.

Fill fuel tank outdoors.

DO NOT overfill tank. Allow space for fuel expansion.

Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources.

DO NOT light a cigarette or smoke.

1.Use clean, fresh, regular UNLEADED fuel with a minimum of 85 octane with equipment. DO NOT use fuel which contains Methanol. DO NOT mix oil with fuel.

2.Clean area around fuel fill cap, remove cap.

BEFORE STARTING THE ENGINE

Add Engine Oil

Place generator on a level surface.

Refer to engine owner’s manual and follow oil recommendations and instructions.

3.Slowly add regular unleaded fuel to fuel tank. Be careful not to fill above the baffle.This allows adequate space for fuel expansion (Figure 2).

Figure 2 — Typical Fuel Expansion Space

TANK

Baffle

FUEL

4.Install fuel cap and wipe up any spilled fuel.

7

Page 7
Image 7
Briggs & Stratton PRO6500 owner manual Before Starting the Engine, Add Fuel, Add Engine Oil, When Adding Fuel

PRO6500 specifications

Briggs & Stratton PRO6500 is a powerful portable generator designed for both home and professional use. Known for its durability and reliability, this generator stands out in the market due to its innovative features and advanced technologies that provide users with an efficient power solution.

One of the main highlights of the PRO6500 is its robust engine. It is equipped with a Briggs & Stratton OHV engine that delivers a strong performance, providing 6500 running watts and 8500 starting watts. This capacity makes it suitable for powering essential appliances during outages or for tools at job sites. The generator features a 7.5-gallon fuel tank, which allows for extended run times, typically around 12 hours at 50% load. This means less time spent refueling and more time enjoying uninterrupted power.

Another significant feature of the PRO6500 is its advanced Wave inverter technology, which produces clean and stable power. This makes it safe for sensitive electronics such as laptops, smartphones, and gaming consoles, ensuring that users can power their devices without fear of damage. The generator also includes a low-emission engine that meets EPA regulations, promoting environmentally friendly operation.

The PRO6500 is designed with convenience in mind. It features an easy-to-use control panel that includes multiple circuit breakers, a start switch, and multiple outlets, allowing users to safely connect various devices and appliances. The generator also has an electric start feature, which eliminates the hassle of manual starting. Just a push of a button is all it takes to get the generator up and running.

Portability is another strong aspect of the PRO6500. It is built with a rugged steel frame and heavy-duty wheels, giving it the ability to be easily transported to different locations, whether in your backyard, on a job site, or during camping trips. The folding handle also makes it simpler to move and store.

Safety features are integrated into the design of the PRO6500. It includes low oil and overload shutdown systems to prevent engine damage and enhance longevity. The generator also has a digital hour meter that keeps track of runtime, which aids users in maintaining proper service intervals.

In conclusion, the Briggs & Stratton PRO6500 is a versatile and powerful generator that offers significant benefits in terms of performance, convenience, and safety. Whether for home use or professional applications, it provides reliable power solutions that users can depend on in various situations.