BSPP Generator

OPERATING THE

GENERATOR

CAUTION

Exceeding generators wattage/amperage capacity can damage generator and/or electrical devices connected to it.

•See “Don’t Overload Generator”.

•Start generator and let engine stabilize before connecting electrical loads.

•Connect electrical loads in OFF position, then turn ON for operation.

•Turn electrical loads OFF and disconnect from generator before stopping generator.

Starting the Engine

Disconnect all electrical loads from the generator. Use the following start instruction steps in numerical order:

1.Make sure unit is on a level surface.

IMPORTANT: Failure to start and operate unit on a level surface will cause the unit not to start or shut down during operation.

2.Turn fuel valve to “On” position (Figure 4).

Figure 4 — Fuel Shut-off Valve

3.Make sure Idle Control switch is in “Off” position (Figure 5).

Figure 5 — Idle Control Switch

4.Follow start instructions given in engine owner’s manual.

NOTE: If engine starts after 3 pulls but fails to run, or if unit shuts down during operation, make sure unit is on a level surface and check for proper oil level in crankcase.

This unit may be equipped with a low oil protection device. See engine manual.

WARNING

Running engines produce heat.Temperature of muffler and nearby areas can reach or exceed 150°F (65°C).

Severe burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc. can catch fire.

•DO NOT touch hot surfaces.

•Allow equipment to cool before touching.

•The generator must be at least 5 feet from structures having combustible walls and/or other combustible materials.

•Keep at least 3 feet of clearance on all sides of generator for adequate cooling, maintenance and servicing.

•In the State of California a spark arrester is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. If you equip the muffler with a spark arrester, it must be maintained in effective working order.

Connecting Electrical Loads

•Let engine stabilize and warm up for a few minutes after starting.

•Plug in and turn on the desired 120 and/or 240 Volt AC, single phase, 60 Hz electrical loads.

•DO NOT connect 240 Volt loads to the 120 Volt duplex receptacles.

•DO NOT connect 3–phase loads to the generator.

•DO NOT connect 50 Hz loads to the generator.

•DO NOT OVERLOAD THE GENERATOR. See “Don’t Overload Generator”.

Stopping the Engine

1.Turn OFF and unplug ALL electrical loads from generator panel receptacles. NEVER start or stop engine with electrical devices plugged in and turned ON.

2.Move idle control switch to “Off” position.

3.Let engine run at no-load for several minutes to stabilize internal temperatures of engine and generator.

4.Move fuel valve to “Off” position.

5.Turn engine off according to instructions given in the engine owner’s manual.

9

Page 8 Page 10
Page 9
Image 9
Briggs & Stratton PRO6500 Operating Generator, Starting the Engine, Connecting Electrical Loads, Stopping the Engine
Page 8 Page 10

PRO6500 specifications

Briggs & Stratton PRO6500 is a powerful portable generator designed for both home and professional use. Known for its durability and reliability, this generator stands out in the market due to its innovative features and advanced technologies that provide users with an efficient power solution.

One of the main highlights of the PRO6500 is its robust engine. It is equipped with a Briggs & Stratton OHV engine that delivers a strong performance, providing 6500 running watts and 8500 starting watts. This capacity makes it suitable for powering essential appliances during outages or for tools at job sites. The generator features a 7.5-gallon fuel tank, which allows for extended run times, typically around 12 hours at 50% load. This means less time spent refueling and more time enjoying uninterrupted power.

Another significant feature of the PRO6500 is its advanced Wave inverter technology, which produces clean and stable power. This makes it safe for sensitive electronics such as laptops, smartphones, and gaming consoles, ensuring that users can power their devices without fear of damage. The generator also includes a low-emission engine that meets EPA regulations, promoting environmentally friendly operation.

The PRO6500 is designed with convenience in mind. It features an easy-to-use control panel that includes multiple circuit breakers, a start switch, and multiple outlets, allowing users to safely connect various devices and appliances. The generator also has an electric start feature, which eliminates the hassle of manual starting. Just a push of a button is all it takes to get the generator up and running.

Portability is another strong aspect of the PRO6500. It is built with a rugged steel frame and heavy-duty wheels, giving it the ability to be easily transported to different locations, whether in your backyard, on a job site, or during camping trips. The folding handle also makes it simpler to move and store.

Safety features are integrated into the design of the PRO6500. It includes low oil and overload shutdown systems to prevent engine damage and enhance longevity. The generator also has a digital hour meter that keeps track of runtime, which aids users in maintaining proper service intervals.

In conclusion, the Briggs & Stratton PRO6500 is a versatile and powerful generator that offers significant benefits in terms of performance, convenience, and safety. Whether for home use or professional applications, it provides reliable power solutions that users can depend on in various situations.
Top Page Image Contents