Power Exhaust (output): Connect the accessory Power Exhaust contactor coil(s) per Fig. 46.
Power Exhaust |
|
|
| |||
| PEC | GRA |
|
|
| |
|
|
|
| |||
|
|
| ||||
|
|
|
| CTB | ||
|
|
|
| THERMOSTAT | ||
|
|
| TAN |
| C | |
|
|
|
| |||
|
|
|
|
| C10362 |
Fig. 46 - RTU-MP Power Exhaust Connections
Space Relative Humidity Sensor - The RH sensor is not used with 548J*14D models at this time.
Communication Wiring - Protocols
General —
Protocols are the communication languages spoken by control devices. The main purpose of a protocol is to communicate information in the most efficient method possible. Different protocols exist to provide different kinds of information for different applications. In the BAS application, many different protocols are used, depending on manufacturer. Protocols do not change the function of a controller; just make the front end user different.
The
per protocol. The 3rd party connection to the
NOTE: Power must be cycled after changing the
Refer to the
Local Access —
BACview6 Handheld: The BACview6 is a keypad/display interface used to connect to the
Virtual BACview: Virtual BACview is a freeware computer program that functions as the BACview6 Handheld. The USB Link interface
RTU-MP Troubleshooting —
Communication LEDs The LEDs indicate if the controller is speaking to the devices on the network. The LEDs should reflect communication traffic based on the baud rate set. The higher the baud rate the more solid the LEDs will appear.
548J*14D
SW3 Protocol Selection
PROTOCOL |
| DS8 | DS7 | DS6 | DS5 | DS4 | DS3 | DS2 | DS1 | |
|
|
|
|
|
|
|
|
|
|
|
BACnet MS/TP |
| Unused | OFF | OFF | OFF | ON | OFF | Select Baud | Select Baud | |
(Master) |
| |||||||||
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
Modbus |
| Unused | OFF | OFF | ON | ON | OFF | Select Baud | Select Baud | |
(Slave) |
| |||||||||
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
N2 |
| Unused | OFF | OFF | OFF | ON | ON | OFF | OFF | |
(Slave) |
| |||||||||
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
LonWorks |
| Unused | ON | ON | OFF | ON | OFF | OFF | OFF | |
|
|
|
|
|
|
|
|
|
|
|
NOTE: |
|
|
|
|
|
|
|
|
|
|
DS = Dip Switch |
|
|
|
|
|
|
|
|
|
|
BACnet MS/TP SW3 example shown |
|
|
|
|
|
|
|
| ||
| Baud Rate Selections |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |
BAUD RATE |
| DS2 |
| DS1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
9600 |
| OFF |
| OFF |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
19,200 |
| ON |
| OFF |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
38,400 |
| OFF |
| ON |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
76,800 |
| ON |
| ON |
|
|
|
|
|
|
C07166
Fig. 47 - RTU-MP SW3 Dip Switch Settings
25