Manuals / Cables to Go / Computer Equipment / Switch

Cables to Go TE100-S55 manual Installing XPressView, What You Need, Processor, Disk Space, Windows

Models: TE100-S55

1 57

Download 57 pages 7.63 Kb

Page 36

Installing XPressView

Installing the XPressView SNMP Management program is easy to do and only takes a few minutes. The supplied SETUP program guides you through the process.

WHAT YOU NEED

To use XPressView, your computer must have the following:

Processor:	386, 486 or Pentium
RAM:	2 megabytes minimum
Disk Space:	10 megabytes minimum
Windows:	3.1, 3.11 or Win95
TCP/IP	Winsock interface
	(It is recommended to set the IP address
	at 168.8.xx.xx, similar to the TE100-
	S55 IP address)
Drive:	1.44 Floppy
Display:	VGA

TO INSTALL XPRESSVIEW

•Run Windows and close all programs that are active.

•Insert the supplied XPressView diskette into your floppy drive.

•From Windows Program Manager or Explorer, click the floppy drive that contains XPressView, and click the SETUP command. The setup screen will appear. Accept or modify the Destination Directory and click NEXT.

•The XPressView program icon will automatically be added to your Windows start screen.

36

Image 36

Cables to Go TE100-S55 manual Installing XPressView, What You Need, Processor, Disk Space, Windows, Tcp/Ip, Drive, Display

Contents

Multifunction Switch/Router Model TE100-S55 for connecting 10Base-T, 100Base-TX, 100Base-FX and ISDN linksProXpressTM User’s GuideTrademarks FCC warningService and support Bulletin Board SystemWorld Wide Web Site About this manual TE100-S55Table of Contents Chapter 3 CONFIGURING THE SWITCHChapter INTRODUCTIONChapter 5 DIAGNOSTICS APPENDICESINDEX Chapter 1 Introduction Fast Ethernet TechnologySwitching Technology Table Chapter 1 -1, Ethernet vs. Fast Ethernet10/100 Switching Technology Benefits of SwitchingIntroducing the TE100-S55 Refer to Appendix D page 49 for more detailRefer to Appendix E page 50 for more detailFeatures of TE100-S55 Chapter 2 Getting Started Cabling Rules and Site PreparationFigure Chapter 2 -1, Example of TE100-S55 wiring environment Figure Chapter 2 -2, 100Base-T cabling rules Unpacking and Setup UNPACKINGTHE FRONT PANEL MOUNTING ATTACHING CABLESFigure Chapter 2 -5, Rack mounting a TE100-S55 POWER ON ADDING OPTIONAL MODULESSOFTWARE SETUP CHECKING STATUS LEDSFigure Chapter 2 -6, TE100-S55 status LEDs Chapter 3 Configuring the Switch IntroductionOut-of-Band Management ATTACHING TO THE RS-232 PORTVT100 TERMINAL Terminal StepVT100 Compatible PCVT100 terminalControl Settings Table Chapter 3 -2, TE100-S55 Settings for Out-of-Band managementSystem display User selectionUSER-SELECTIVE PARAMETERS From the Filtering Data Base menu, you can Disable, Forward or Block up to 16 MAC addresses for each port on the TE100-S55. This feature allows you to create a virtual LAN, filtering each segment for added performance Spanning Tree Algorithm Table Chapter 3 -3, User-selective STA parameters AT THE BRIDGE LEVEL AT THE PORT LEVEL TIMERS ILLUSTRATION OF STA Figure Chapter 3 -2, Before Applying the STA Rules Figure Chapter 3 -3, After Applying the STA RulesRoot Port Designated PortPage Chapter 4 SNMP Management Installing XPressView TO INSTALL XPRESSVIEWWHAT YOU NEED ProcessorStarting XPressView START FROM SCRATCHOperating XPressView OPEN AN EXISTING ENVIRONMENTSELECT A DEVICE VIEW/MODIFY SWITCH CONFIGURATION MODIFY THE SPANNING TREE ALGORITHMMONITOR NETWORK TRAFFIC Display in TEXT format Display in GRAPHIC formatChapter 5 Diagnostics Power-On Self TestSystem Status LEDs System error LEDError Port error LEDSystem Diagnostic LEDs System Utilization LEDsPort Status LEDs Appendix A Switch Default setting AppendicesAppendix B RS-232 Pin Specification Appendix C RJ-45 Pin Specification The standard RJ-45 receptacle/connectorThe Standard Category 3 cable, RJ-45 pin assignment The pin assignment for Category 5, 4-pair cross-over cableContact How to Install the 10Base-T module Appendix D 10Base-T ModuleHow to Install the 100Base-FX/TX module Appendix E 100Base-FX/TX ModulePage How to Install the ISDN module Appendix F ISDN ModuleAttach the ISDN phone line into the RJ-11 port of the ISDN module Appendix G Hardware Specifications SWITCH SPECIFICATIONPORT SPECIFICATION 5 x 10/100Mbps LAN ports fixed 8 x 10Mbps LAN ports optional module1 x 100Base-FX/TX LAN port optional module 1 x ISDN WAN port optional moduleINDEX Modify the Spanning Tree Algorithm