Manuals / Cables to Go / Computer Equipment / Switch

Cables to Go TE100-S55 manual Appendix G Hardware Specifications, Switch Specification

Models: TE100-S55

1 57

Download 57 pages 7.63 Kb

Page 54

Appendix G Hardware Specifications

SWITCH SPECIFICATION

•Complies to IEEE 802.3 CSMA/CD 10Base-T, 100Base-TX, 100Base-FX Ethernet Standards

•Complies to IEEE 802.1d Spanning Tree, IEEE 802.2 LLC, and ISO 8807-3 standards

•Switched IEEE 802.3 MAC layer frame size: 64-1518

•NWAY Auto-negotiation for each network port providing auto-detection of connected cable type, auto-sensing of full or half duplex signaling and auto-configuration

•Store-and-forward packet switching

•Native SNMP management support with Ethernet MIB II (RFC 1284) and bridge MIB (RFC 1286)

•VLAN support

•4,096 maximum entries for MAC Address Table

•Comprehensive LED display of the system/port status

•128KB EEPROM (flash memory) for firmware upgrade

•One RS-232D (DB-9) port for Out-of-Band management (asynchronous, 8-bit data, 1 stop bit, no parity, 19.2K baud)

•Rack mountable (Fits standard 2U EIA 19” rack)

•Five 10/100Mbps LAN ports built-in

•Optional slot for add-on modules

PORT SPECIFICATION

54

Image 54

Cables to Go TE100-S55 manual Appendix G Hardware Specifications, Switch Specification, Port Specification

Contents

ProXpressTM Multifunction Switch/Router Model TE100-S55for connecting 10Base-T, 100Base-TX, 100Base-FX and ISDN links User’s GuideTrademarks FCC warningService and support Bulletin Board SystemWorld Wide Web Site About this manual TE100-S55Chapter Table of ContentsChapter 3 CONFIGURING THE SWITCH INTRODUCTIONChapter 5 DIAGNOSTICS APPENDICESINDEX Chapter 1 Introduction Fast Ethernet TechnologySwitching Technology Table Chapter 1 -1, Ethernet vs. Fast Ethernet10/100 Switching Technology Benefits of SwitchingIntroducing the TE100-S55 Refer to Appendix E Refer to Appendix Dpage 49 for more detail page 50 for more detailFeatures of TE100-S55 Chapter 2 Getting Started Cabling Rules and Site PreparationFigure Chapter 2 -1, Example of TE100-S55 wiring environment Figure Chapter 2 -2, 100Base-T cabling rules Unpacking and Setup UNPACKINGTHE FRONT PANEL MOUNTING ATTACHING CABLESFigure Chapter 2 -5, Rack mounting a TE100-S55 POWER ON ADDING OPTIONAL MODULESSOFTWARE SETUP CHECKING STATUS LEDSFigure Chapter 2 -6, TE100-S55 status LEDs Chapter 3 Configuring the Switch IntroductionOut-of-Band Management ATTACHING TO THE RS-232 PORTVT100 Compatible VT100 TERMINALTerminal Step PCVT100 terminalSystem display Control SettingsTable Chapter 3 -2, TE100-S55 Settings for Out-of-Band management User selectionUSER-SELECTIVE PARAMETERS From the Filtering Data Base menu, you can Disable, Forward or Block up to 16 MAC addresses for each port on the TE100-S55. This feature allows you to create a virtual LAN, filtering each segment for added performance Spanning Tree Algorithm Table Chapter 3 -3, User-selective STA parameters AT THE BRIDGE LEVEL AT THE PORT LEVEL TIMERS ILLUSTRATION OF STA Root Port Figure Chapter 3 -2, Before Applying the STA RulesFigure Chapter 3 -3, After Applying the STA Rules Designated PortPage Chapter 4 SNMP Management WHAT YOU NEED Installing XPressViewTO INSTALL XPRESSVIEW ProcessorStarting XPressView START FROM SCRATCHOperating XPressView OPEN AN EXISTING ENVIRONMENTSELECT A DEVICE VIEW/MODIFY SWITCH CONFIGURATION MODIFY THE SPANNING TREE ALGORITHMMONITOR NETWORK TRAFFIC Display in TEXT format Display in GRAPHIC formatChapter 5 Diagnostics Power-On Self TestError System Status LEDsSystem error LED Port error LEDSystem Diagnostic LEDs System Utilization LEDsPort Status LEDs Appendix A Switch Default setting AppendicesAppendix B RS-232 Pin Specification Appendix C RJ-45 Pin Specification The standard RJ-45 receptacle/connectorThe Standard Category 3 cable, RJ-45 pin assignment The pin assignment for Category 5, 4-pair cross-over cableContact How to Install the 10Base-T module Appendix D 10Base-T ModuleHow to Install the 100Base-FX/TX module Appendix E 100Base-FX/TX ModulePage How to Install the ISDN module Appendix F ISDN ModuleAttach the ISDN phone line into the RJ-11 port of the ISDN module Appendix G Hardware Specifications SWITCH SPECIFICATIONPORT SPECIFICATION 1 x 100Base-FX/TX LAN port optional module 5 x 10/100Mbps LAN ports fixed8 x 10Mbps LAN ports optional module 1 x ISDN WAN port optional moduleINDEX Modify the Spanning Tree Algorithm