Manuals / Cabletron Systems / Computer Equipment / Network Card

Cabletron Systems user manual FOT-F3 USER’S MANUAL

Models: F3

1 44

Download 44 pages 168 b

Page 3

NOTICE

Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made.

The hardware, firmware, or software described in this manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

© Copyright 1996 by: Cabletron Systems, Inc.,

P.O. Box 5005, Rochester, NH 03866-5005

All Rights Reserved

Printed in the United States of America

Part Number: 9030461-01 July 1996

LANVIEW is a registered trademark of Cabletron Systems, Inc.

LAN-MD,FOT-F3,FOMIM-32/36/38,MMAC, NBR-220, and IRM are trademarks of Cabletron Systems, Inc.

Velcro is a registered trademark of Velcro Industries, B.V.

Printed on

Recycled Paper

FOT-F3 USER’S MANUAL

i

Image 3

Cabletron Systems user manual FOT-F3 USER’S MANUAL

Contents

FOT-F3 FIBER OPTIC TRANSCEIVER USER’S MANUAL Page FOT-F3 USER’S MANUAL FCC NOTICE DOC NOTICEFOT-F3 USER’S MANUAL FOT-F3 USER’S MANUAL VCCI NOTICEDECLARATION OF CONFORMITY FOT-F3 USER’S MANUALuse in a Commercial or Light CHAPTER CONTENTSINSTALLATION REQUIREMENTS INSTALLATIONCHAPTER 4 TESTING AND TROUBLESHOOTING APPENDIX A SPECIFICATIONSCONTENTS CHAPTER INTRODUCTION 1.1 USING THIS MANUAL1.3 OVERVIEW OF THE FOT-F3 1.2 CONVENTIONS1.3.1 Connections FOT-F3Figure 1-1 FOT-F3 1.3.2 Distance and Cable Type Signal Quality Error SQE TestFigure 1-2 LANVIEW LEDs 1.3.3 LANVIEW LEDsRCV Receive PWR PowerSQE Signal Quality Error Test Function XMT Transmit1.3.4 Application Figure 1-3 FOT-F3 Setup, ExampleFigure 1-4 FOT-F3 Setup, Example 1.4 GETTING HELP anonymousyour email address 1-10 1.5 RELATED MANUALSCabletron Systems LAN-MD Portable Ethernet Tester User’s Manual Any previous Return Material Authorization RMA numbersCHAPTER INSTALLATION REQUIREMENTS 2.1 NETWORK DESIGN GUIDELINES2.1.1 Fiber Optic Requirements CHAPTER 2 INSTALLATION REQUIREMENTS 2.1.2 AUI Cable Requirements3.1 UNPACKING THE FOT-F3 CHAPTER INSTALLATION3.2.1 Setting the SQE Switch 3.2 CONNECTING THE FOT-F3 TO THE NETWORKFigure 3-1 SQE Switch 3.2.2 Connecting the AUI CableFigure 3-2 AUI Connection 3.2.3 Connecting the Fiber Optic Cable Connect the fiber optic cable to the FOT-F3 as follows Figure 3-3 ST Connectors 3.3 SURFACE MOUNTING THE FOT-F3 3.4.1 Cable Strain Relief for Surface Mounted FOT-F3 3.4 CABLE SUPPORT INSTALLATIONFigure 3-4 Surface Mounting the FOT-F3 3.4.2 Cable Strain Relief for Non-Mounted FOT-F3CABLE SUPPORT INSTALLATION FOT-F3 USER’S MANUAL3-11 CHAPTER 3 INSTALLATION 3-12FOT-F3 USER’S MANUAL CHAPTER TESTING AND TROUBLESHOOTING 4.1 INSTALLATION CHECK-OUT4.1.1 Testing the Fiber Optic Link Segment 5. Disconnect the jumpers from the barrel connector Figure 4-1 Installation Checkout 4.1.2 Testing the FOT-F3 Fiber Optic Transceiver4.2 USING LANVIEW Collision CLN LED Figure 4-2 LANVIEW LEDs Optical Link OK LNK LEDSignal Quality Error SQE Test Function LED Receive RCV LEDTransmit XMT LED Power PWR LED FOT-F3 USER’S MANUAL CHAPTER 4 TESTING AND TROUBLESHOOTINGParameter APPENDIX A SPECIFICATIONSTable A-1 Fiber Optic Interface Specifications A.1 FIBER OPTIC INTERFACEMinimum Table A-1 Fiber Optic Interface Specifications ContinuedParameter TypicalTable A-2 Power Supply Specifications A.2 AUI CONNECTORA.3 POWER SUPPLY Figure A-1 AUI Connector Pinout IdentificationA.5 AGENCY APPROVALS Table A-3 Environmental SpecificationsSafety A.4 ENVIRONMENTAL