Manual de Instrucciones
DG201900CK
Mantenimiento
Limpieza
Todas las piezas de plástico deben limpiarse con un paño húmedo. NUNCA use solventes para limpiar piezas de plástico. Podrían disolverse o dañar el material de alguna otra manera.
La herramienta no funciona
En caso de que la herramienta no funcione, asegúrese de que la batería esté cargada e instalada en el taladro.
Servicio a la batería
La batería que se proporciona con este taladro se descargará sola y perderá algo de su capacidad con el paso del tiempo. Por lo tanto, si se almacena sin usar durante un período de tiempo prolongado, puede que sea necesario recargarla antes de usarla. Para obtener el mayor rendimiento de sus baterías, se recomienda recargar la batería cada 2 ó 3 meses y cuando se recargue, se debe retirar la batería del cargador después de 2 ó 3 horas de carga.
Remoción / reemplazo del portabrocas
Si fuera necesario reemplazar el portabrocas, siga los pasos siguientes para hacerlo:
•Retire la batería del taladro.
•Gire el collar de embrague hasta que el símbolo de broca quede alineado con la flecha que se encuentra en la parte superior de la carcasa del taladro.
•Abra completamente las mordazas del portabrocas desatornillando el manguito del portabrocas hacia la izquierda (cuando se ve el portabrocas desde su extremo).
•Ubique el tornillo izquierdo dentro del portabrocas y con la punta de destornillador adecuada quite este tornillo girándolo hacia la derecha.
•Introduzca el brazo corto de una llave hexagonal o Allen de 3/8 pulg. dentro del portabrocas y apriete las mordazas del portabrocas sobre las partes planas de esta llave.
•Con un martillo o similar, golpee el brazo largo de la llave con un golpe seco de modo que el portabrocas gire hacia la izquierda.
•Una vez que haya aflojado el portabrocas, retire la llave y desatornille el portabrocas de su vástago.
•Para cambiar el portabrocas por otro, invierta los pasos descritos anteriormente. Siempre mantenga las roscas del vástago, las roscas del portabrocas y el tornillo sujetador sin residuos.
Servicio
El servicio a esta herramienta debe ser realizado únicamente por personal calificado en reparación y por un CENTRO DE SERVICIO AUTORIZADO. El servicio o mantenimiento realizados por personas no calificadas puede provocar riesgo de lesiones.
Para obtener información con relación al funcionamiento o reparación de este producto, sírvase llamar al
General Power Tool Safety Warnings
(Continued)d)Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e)Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
f)Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
g)If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce
h)CALIFORNIA PROPOSITION 65
You can create dust when you cut,
j)Some wood contains preservatives which can be toxic. Take extra care to prevent inhalation and skin contact when working with these materials. Request and follow all safety information available from your material supplier.
k)
Do not misuse this product. Excessive exposure to vibration, work in awkward positions, and repetitive work motions can cause injury to hands and arms. Stop using any tool if discomfort, numbness, tingling, or pain occur, and consult a physician.
l) Always work in a well- |
ventilated area. Wear an |
m) Keep hands away from |
rotating parts. |
n) Use clamps or another |
practical way to secure the |
workpiece to a stable |
platform. Never hold work in |
your hand, lap, or against |
other parts of your body |
when drilling. |
o) Before using the battery |
charger, read all instructions |
on the charger, battery, and |
product. |
b) Do not use the power tool if |
the switch does not turn it on |
and off. Any power tool that |
cannot be controlled with the |
switch is dangerous and must be |
repaired. |
c) Disconnect the plug from the |
power source and/or the |
battery pack from the power |
tool before making any |
adjustments, changing |
accessories, or storing power |
tools. Such preventive safety |
measures reduce the risk of |
starting the power tool |
accidentally. |
d) Store idle power tools out of |
the reach of children and do |
not allow persons unfamiliar |
with the power tool or these |
instructions to operate the |
power tool. Power tools are |
dangerous in the hands of |
untrained users. |
e) Maintain power tools. Check |
for misalignment or binding |
of moving parts, breakage of |
parts and any other condition |
that may affect the power |
tool’s operation. If damaged, |
have the power tool repaired |
before use. Many accidents are |
caused by poorly maintained |
power tools. |
Para Ordenar Repuestos o Asistencia Técnica, Sírvase Llamar al Distribuidor Más Cercano a Su Domicilio
sand, drill or grind materials such as wood, paint, metal, concrete, cement,
p) Do not attempt to |
disassemble the battery or |
remove any component |
projecting from the battery |
f) Keep cutting tools sharp and |
clean. Properly maintained |
cutting tools with sharp cutting |
| Número del |
Descripción | Repuesto |
|
|
Cargador – 19,2V | DG029600AV |
Batería – 19,2V | DG201900AV |
Portabroca – 3/8 po | DG029900AV |
Tornillo de fijación | SX173400AV |
Caja | DG030000AV |
|
|
S’il vous plaît fournir l’information suivante:
-Número del modelo
-Código impreso
-Descripción y número del repuesto según la lista de repuestos
Dirija toda la correspondencia a:
Campbell Hausfeld
Attn: Parts Department
100 Production Drive
Harrison, OH 45030 U.S.A .
or other masonry. This dust often contains chemicals known to cause cancer, birth defects, or other reproductive harm. Wear protective gear.
i)
This product or its power cord contains lead, a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
terminals. Fire or injury may |
result. |
4) Power tool use and care |
a) Do not force the power tool. |
Use the correct power tool for |
your application. The correct |
power tool will do the job better |
and safer at the rate for which it |
was designed. |
edges are less likely to bind and |
are easier to control. |
g) Use the power tool, |
accessories and tool bits etc. |
in accordance with these |
instructions, taking into |
account the working |
conditions and the work to |
be performed. Use of the |
power tool for operations |
different from those intended |
could result in a hazardous |
situation. |
30 Sp | 3 |