Lavadoras a Presión
Hidrolavadora de Eje Vertical
1
1617
18
21 
20
219
4
3
Pressure Washers
Pre-Operation (Continued)
7.Attach the lance with nozzle to the gun (see Figure 7).
TRIGGER SAFETY LATCH |
|
In the engaged position, the trigger |
|
safety latch prevents the gun from being |
|
triggered accidentally. Push the latch fully |
|
down to engage it (See Figure 8 and 9). |
|
Always engage the trigger safety latch | Figure 7– Attach lance to gun |
when the unit is not in use. |
|
Engaged |
| Disengaged |
|
|
|
Figure 8 - Trigger locked | Figure 9 - Trigger unlocked |
Operation
5 
14
12
1113
No. |
|
| Número |
|
| |
de |
| Descripción | del | Ctd. | ||
Ref. |
| repuesto |
|
| ||
1 |
| Tubo del mango | PM343715AV | 1 |
| |
2 | * | Perno de 6,4 mm (1/4") - 20 (mango) | PM001903AV | 2 |
| |
3 | * | Arandela plana | PM002000AV | 14 |
| |
4 | * | Tuerca de seguridad de nilon de |
|
|
| |
|
|
| 6,4 mm (1/4") - 20 | ST073808AV | 7 |
|
| 5 | * | Perno de 6,4 mm (1/4") - 20 (base) | PM001902AV | 3 |
|
6 |
| Pata izquierda | PM344828BH | 1 |
| |
7 |
| Pata derecha | PM345100BH | 1 |
| |
1. Surface Preparation
The following cleaning procedure will help you organize your cleaning task and ensures that you will achieve the best results in the shortest amount of time. Remember to use the spraying / cleaning techniques mentioned in the following section.
Before starting a pressure washer cleaning job, prepare the surface you
DO NOT refuel a hot engine. Refueling a hot engine could cause a fire. Use only
fresh, clean regular or unleaded gasoline. Close the fuel shutoff valve during refueling.
3.Attach a garden hose to the inlet side of the pump and connect it to the water supply. Use a hose with an internal diameter (I.D.) of 5/8 inch (1.58 cm) and a length of 50 ft. (15 m) or less.
Some local
moving the choke ring fully to the right. Turn the ignition switch to “ON”.
7. Start the engine. Unlock the |
trigger safety latch on the gun (See |
Figure 9). Grasp the starter rope |
and brace one foot on the chassis. |
Point the gun in a safe direction. |
While squeezing the trigger on the |
gun, pull the starter rope rapidly |
and firmly (See Figure 10). |
10
7
8 | Defensa de caucho | AL062300AV | 2 |
intend to clean. Clear furniture from
plumbing codes
Continue holding the rope as it |
6
8 9
Para ordenar repuestos, sírvase lla- mar al
Sírvase darnos la siguiente información:
-Número del modelo
-Número de série (de haberlo)
-Descripción y número del repuesto según la lista de repuestos
9 | * | Tornillo autorrosc. 0,64 cm (1/4") |
|
|
|
| - 20 x 19,1 mm (3/4") | MJ102100AV | 2 |
10 |
| Rueda | WA120100AV | 2 |
11 |
| Tuerca de presión | AL066300AV | 2 |
12 | * | Perno de 6,4 mm (1/4") - 20 (Eje) | PM001904AV | 2 |
13 |
| Eje | PM344831BH | 1 |
14 |
| Placa de base | GN004530AV | 1 |
15 |
| Tubo del detergente (not shown) | PM013800AV | 1 |
16 |
| Pistola | PM243000AV | 1 |
17 |
| Anillo en O (pistola) | PM245800SV | 1 |
18 |
| Manguera | PM344301AV | 1 |
19 |
| Lanza turbo (optional) | PM243500AV | 1 |
20 |
| Lanza alta presión | PM268500AV | 1 |
21 |
| Tanque de detergente | PM268680AJ | 1 |
22 |
| Replacement Pump | PM341000SJ | 1 |
*Artículo disponible en ferreterías locales.
the area and make sure that all windows and doors are closed tightly. Also, protect all plants and trees near the cleaning area with a drop cloth. A covering ensures that your plants won’t be sprayed by the detergents.
2. Start Up
ALWAYS use the following start up procedure to ensure that the unit is started safely and properly.
If water has frozen
require backflow prevention when connecting to a fresh water supply. Install a backflow preventer upstream from the pump if necessary.
a. If inlet water pressure is over 100 psi, install a regulating water valve at the garden hose connection.
b.Do not exceed 100˚ F (38˚ C) inlet water temperature.
NOTE: The inlet water supply must have a minimum flow rate of 5 gpm (19 lpm).
4. Turn the water supply ON.
Never run the unit
returns. Repeat these steps until |
the engine starts. |
Puede escribirnos a: Campbell Hausfeld Attn: Customer Service 100 Production Drive Harrison, OH 45030
28 Sp
in the pressure washer, thaw the pressure washer in a warm room before starting. DO NOT pour hot water on or into the pump; internal parts will be damaged.
1.Check engine oil levels. Add oil as necessary.
2.Check fuel level. Add unleaded gasoline (rated 86 octane or higher) as required
dry. Be sure the
water supply is completely turned on before operating the unit.
5.Trigger the gun until water sprays smoothly from the tip indicating that all air is purged from the system. Lock the trigger safety latch.
6.Open the fuel valve by turning the knob counterclockwise until it stops. Close the choke (if engine is cold) by
Figure 10 - Start the engine
www.chpower.com
5
