CBM America iDP3240 ESC c 3 n

— 88 —

ESC c 3 n

[Function] Selecting the Paper Sensor valid for a paper end signal output

[Code] <1B>H<63>H<33>H<n>

[Range] 0 n 255

[Outline] This command selects by which Paper Sensor a paper end signal

should be output. Each bit for “n” has the following meaning:

Bit Position Value

0 Paper Near-end Disabled Enabled

1 Paper Near-end Disabled Enabled

2 Paper end Disabled Enabled

3 Paper end Disabled Enabled

4 Undefined

5 Undefined

6 Undefined

7 Undefined

[Caution] This command is valid only for the parallel interface.

Bits 1 and 2, and bits 2 and 3 are valid if either bit is “1”. If all

bits are set to be invalid, the paper end signal always indicates

that paper is available.

[Default] n = 15

Contents

Main Declaration of Conformity IMPORTANT SAFETY INSTRUCTIONS WICHTIGE SICHERHEITSANWEISUNGEN Page GENERAL PRECAUTIONS SAFETY PRECAUTIONS i WARNING CAUTION WARNING PRECAUTIONS FOR INSTALLATION PRECAUTIONS FOR HANDLING HOT AREA: DAILY MAINTENANCE Page THE TABLE OF CONTENTS 1. GENERAL OUTLINE ................................................................... 1 2. BASIC SPECIFICATIONS ............................................................4 3. OUTER APPEARANCE AND COMPONENT PARTS.................. 9 4. OPERATION .............................................................................. 10 6. PARALLEL INTERFACE............................................................. 29 7. SERIAL INTERFACE.................................................................. 34 9. MAINTENANCE AND SERVICE ...............................................41 8. DRAWER KICK-OUT CONNECTOR AND POWER CONNECTOR... 39 10. PRINT CONTROL FUNCTIONS ..............................................42 11. CHARACTER CODES TABLE................................................ 141 12. APPENDIX 1. PAGE MODE .................................................. 152 13. APPENDIX 2. BIDIRECTIONAL PARALLEL INTERFACE ........158 Page INHALT <<<German >>> 4. BETRIEB .................................................................................. 179 5. EINSTELLEN DER DIP-SCHALTER......................................... 194 6. PARALLELE SCHNITTSTELLE................................................ 198 Page 1. GENERAL OUTLINE 1.1 Features 1.2 Unpacking 1.3 Before using the printer 2. BASIC SPECIFICATIONS 2.1 Model Classification iDP3240 - R F 120 5 2.2 Basic Specifications 2.3 Print Paper Specifications 2.3.1 Recommended Paper 2.3.2 Print Position and Barcode Printing Page 9 3. OUTER APPEARANCE AND COMPONENT PARTS 3.1 iDP3240 4. OPERATION 4.1 Connecting the AC Adapter and AC Power Cord 4.2 Connecting Interface Cables Page Page Page Page 4.4.2 Setting Paper Rolls when Easy Loading is Disabled (5.2 DS1-3 ON) Page Page 4.7 Releasing a Locked Cutter 4.8 Cleaning the Print Head 4.9 Operation Panel and Error Indication Page 4.10 Self Printing Starting hexadecimal dump Quitting hexadecimal dump 4.11 Hexadecimal Dump 5. SETTING DIP SWITCHES 5.1 Location of DIP Switches Parallel Interface Serial Interface 5.2 Table for Setting DIP Switches DIP switch 1 Note: If print density is set to level 2 or over, print speed may decrease. Print density (DIP switch 1) Selection of Character Code tables (DIP switch 2) DIP switch 2 * : Depends on destinations. Page 6. PARALLEL INTERFACE 6.1 Bidirectional Parallel Interface (IEEE1284) 6.1.1Compatibility Mode (Host Printer communication : Centronics compliant) 6.1.2 Reverse Mode (Printer Host communication) 6.1.3 Connector Pin Configuration 6.2 Description of Input and Output Signals 6.2.1 Input and Output Signals 6.2.2 Electrical Characteristics 6.2.3 Timing Chart (Compatibility Mode) 6.2.4 Data Reception Control 6.2.5 Buffering 7. SERIAL INTERFACE 7.1 Specifications 7.2 Connector Pin Configuration 7.3 Description of Input and Output Signals 7.3.1 Input and Output Signals 7.3.2 Error Detection 7.3.3 Data Reception Control 7.3.4 Buffering Page 8. DRAWER KICK-OUT CONNECTOR AND POWER CONNECTOR 8.1 Specifications of Drawer Kick-Out Connector 8.1.1 Drawer Kick-Out drive signal 8.1.2 Electrical characteristics 8.1.3 Connector Pin Configuration 8.2 Specifications of the Power Connector +24V N.C GND FG 9. MAINTENANCE AND SERVICE * 10. PRINT CONTROL FUNCTIONS 10.1 Command List * Command relative to NV memory * 10.2 Command Details 10.2.1 Description of Each Item XXXX 10.2.2 Command Details HT LF CR FF CAN DLE EOT n Page Page DLE ENQ n DLE DC4 n m t ESC FF ESC SP n Page ESC ! n Page ESC $ n1 n2 Page ESC % n ESC & s n m [a [p] s a] mn+1 65 [Example] Font A Font B ESC * m n1 n2 [ d ] k Page ESC n ESC 2 ESC 3 n ESC = n ESC ? n ESC @ ESC D { n } k NUL ESC E n ESC G n ESC J n ESC L ESC M n ESC R n ESC S ESC T n Page ESC W xL xH yL yH dxL dxH dyL dyH Page ESC \ nL nH ESC a n ESC c 3 n ESC c 4 n ESC c 5 n ESC d n ESC p m n1 n2 ESC t n ESC { n GS ! n Page GS $ nL nH GS * n1 n2 [ d ] n1 n2 8 Page GS (A pL pH n m GS / m GS : GS B n GS H n Page GS I n GS L nL nH GS P x y GS V m ......... (1) GS V m n ..... (2) GS W nL nH A GS \ nL nH GS ^ n1 n2 n3 GS a n (1) 1st byte (Printer information) (2) 2nd byte (Error occurrence information) (3) 3rd byte (Paper Sensor information) Page GS f n GS h n GS k m [d1 ..... dk] NUL GS k m n [d1 ...... dn] Page Page Page Page Page Page Page GS r n Page GS v 0 m xL xH yL yH d1...dk Page GS w n FS g1 m a1 a2 a3 a4 nL nH d1dk [Function] [Code] [Range] [Outline] [Details] Page FS g2 m a1 a2 a3 a4 nL nH [Function] [Code] [Range] [Outline] [Details] [Caution] [Reference] F S p n m Page F S q n [xL xH yL yH d1dk] 1 [xL xH yL yH d1dk] n Page Page Page Page Page Page Page Page Page Page Page Page 11.2 International Character Codes Table 12. APPENDIX 1. PAGE MODE 12.1. Overview 12.2 Mapping of print data in the print area 154 154 A A [Mapping Positions for Print Data] Baseline Print Area Mapping Direction 12.2.1 Example of the Use of PAGE MODE Page Page 13. APPENDIX 2. BIDIRECTIONAL PARALLEL INTERFACE 13.1 Overview 13.1.1 Parallel Interface Communication Modes 159 13.1.2 Interfacing Phases 13.2 Negotiation 13.2.1 Overview 13.2.2 Negotiation Procedure 13.2.3 Precautions 13.2.4 Data Communication from Printer to Host 13.2.4.1 Nibble Mode 13.2.4.2 Byte Mode 13.2.5 Device ID 13.2.6 Termination Page 14. APPENDIX 3. IDENTIFICATION OF SEND STATUS 167 15. APPENDIX 4. OUTLINE DRAWING Unit : mm 15.1 iDP3240 Page 16. APPENDIX 5. BLOCK DIAGRAM Page ALLGEMEINE VORSICHTSMASSNAHMEN WARNUNG i ACHTUNG SICHERHEITSVORSCHRIFTEN WARNUNG VORSICHTSMASSNAHMEN FR DIE INSTALLATION VORSICHTSMASSNAHMEN FR DIE HANDHABUNG HEISSER BEREICH: Page TGLICHE WARTUNGSARBEITEN 4. BETRIEB 4.1 Anschlieen des Netzteils und Netzkabels 4.2 Anschlieen der Schnittstellenkabel 4.3 Anschlieen des Drawer Kickout-Steckers Page Page Page 4.4.2 Einlegen von Papierrollen bei deaktiviertem einfachen Ladevorgang (5.2DS1-3 ON) 4.5 Entfernen von Papierrollenresten 4.6 Beseitigen von Papierstaus 4.7 Freigeben eines verriegelten Papierschneiders 4.8 Reinigen des Druckkopfes 4.9 Bedienungsfeld und Fehleranzeige Page 4.10 Drucktest Starten des Hexdump Beenden des Hexdump 4.11 Hexdump 5. EINSTELLEN DER DIP-SCHALTER 5.1 Position der DIP-Schalter Serielle Schnittstelle Parallele Schnittstelle 5.2 DIP-Schaltertabelle DIP-Schalter 1 Druckdichte (DIP-Schalter 1) Page DIP-Schalter 3 DIP-Schalter 4 Baud-Rate (DIP-Schalter 4) 6. PARALLELE SCHNITTSTELLE 6.1 Bidirektionale parallele Schnittstelle (IEEE1284) 6.1.1 Kompatibilittsmodus (Host Druckerkommunikation: Centronics-kompatibel) 6.1.2 Reverse-Modus (Drucker Hostkommunikation) 6.1.3 Belegung der Anschlustifte 6.2.1 Eingangs- und Ausgangssignale 6.2 Beschreibung von Eingangs- und Ausgangssignalen 6.2.2 Elektrische Kenndaten 6.2.3 Timing-Tabelle (KompatibilittsModus) 6.2.4 Datenempfangssteuerung 6.2.5 Datenpufferspeicher 7. SERIELLE SCHNITTSTELLE 7.1 Technische Daten 7.2 Belegung der Anschlustifte 7.3 Beschreibung der Eingangs- und Ausgangssignale 7.3.1 Eingangs- und Ausgangssignale 7.3.2 Fehlererkennung 7.3.3 Datenempfangssteuerung 7.3.4 Pufferung Page 8. DRAWER KICKOUT-ANSCHLUSS UND STROMANSCHLUSS 8.1 Technische Daten des Drawer KickOut-Anschlusses 8.1.1 Drawer KickOut-Treibersignal 8.1.2 Elektrische Kenndaten 8.1.3 Belegung der Anschlustifte 8.2 Technische Daten des Stromanschlusses +24V N.C GND FG 9. WARTUNG UND KUNDENDIENST