PYROMASTER@ UVHB26 Vent-Free Heaters

0 4. OPTIONAL FK24 FAN HOOK-UP

FAN OPERATION

NOTE: The FK24 fan should be installed before

the mantel cabinet is complete. Later installation will be more difficult.

1.Remove the two (2) screws holding the screen

rods inside the bay top. Remove the screen and rods then set aside.

2.Remove the bay top by removing three (3) screws securing it to the combustion dome.

3.Tip out and lift the bay top and set aside.

4.Remove three (3) nuts securing the fan bracket to the back of the heater.

5.Remove the (2) screws holding the bracket to the fan. Discard this bracket.

6.Remove the two (2) wires attached to the fan and assemble the fan to the bracket as shown

in figure 6.

7.Attach the fan assembly to the back of the heater with the three (3) nuts.

8.Attach the electrical flag connectors to the fan motor using the wire extension (See fig. 5.)

9.Feed the wire down the 1-inch diameter hole in the left side of the radiant shield. Push plastic bushing in hole.

10.Hook the wire extension to the wire leads from the fan control box. NOTE: These leads were hooked to the motor earlier.

11.Mount the thermo-disc to the shield under the burner pan and secure with two (2) nuts.

12.Mount the fan on-off control to the base with

the studs provided and secure with two (2) nuts.

13.Feed the plug through the 4" x 5" hole on the left side of the heater and plug into a wall receptacle.

14.Repeat steps 1 through 3 to reassemble the heater.

The FK24 fan has a heat sensor that will not allow the fan to come on until heater reaches a

preset temperature, approximately 100-120°F. Once the heater reaches temperature use the speed control knob to turn fan on and off to adjust fan speed.

05. FINAL ASSEMBLY

1.Final assembly is accomplished by lifting the mantel cabinet overtop of the heater behind the brass trim pieces.

2.NOTE: The mantel is designed to fit flush to the wall as a freestanding unit. If desired, it may be secured to the wall with nails or screws (not provided).

TEMPERATURE ~AN

SENSOR,

CONTROL~ ~ .

~SPEED

r;. WireExtension

FP394A

Fig.

5. Wiring

diagram.

 

 

 

 

 

 

 

 

 

 

 

 

/

 

-

SCREWS

 

 

 

HEXNUT

 

 

--

 

 

 

 

 

 

 

 

 

 

 

 

FANBRACKET

 

 

o!

 

',.

 

 

 

0'

 

0

(""'

l,:

.

FAN

 

RADIANT

 

 

"",

 

. ':'

 

 

 

SHIELD

 

 

..

.

V

 

 

 

 

 

/ ,0 '//~

 

/,"

 

 

 

 

 

,...

.

 

-4

 

 

 

 

 

 

 

 

.-/

 

 

 

 

 

 

 

':.;:;,

 

 

BURNER

PAN

 

 

 

 

 

 

 

 

SHIELD

 

 

 

 

 

 

 

//.

 

THERMO

DISK

 

 

 

 

 

 

 

 

 

 

 

 

 

 

, /.

...-

 

HEX NUT

 

 

 

 

 

 

'.

 

I

 

-:-

 

 

 

 

I/ ~~~~,

 

 

 

TO

 

 

 

 

 

 

RECEPT,o,C:"'O

 

 

 

 

 

 

'1nEOSTAT

 

 

 

 

 

 

 

 

 

 

 

 

FP732

Fig.

6. Parts

identification,

 

 

 

 

 

)

.)

~",.I

)

8

Page 7 Page 9
Page 8
Image 8
CFM warranty PYROMASTER@ UVHB26 Vent-Free Heaters, FAN Operation
Page 7 Page 9

UVHB26 specifications

The CFM UVHB26 is a cutting-edge vehicle equipped with advanced technology and features that elevate its performance and efficiency, making it a standout in the market. Designed for versatility and reliability, the UVHB26 caters to a wide range of applications including transportation, logistics, and utility services.

One of the key highlights of the CFM UVHB26 is its robust engine, which delivers a powerful performance while ensuring fuel efficiency. The vehicle employs a state-of-the-art turbocharged engine that not only enhances horsepower but also optimizes fuel consumption, making it an environmentally friendly option for modern-day driving. This engine is designed to tackle tough terrains and deliver consistent performance, ensuring that it meets the demands of various operational tasks.

The UVHB26 features an advanced all-wheel-drive system that provides superior traction across different surfaces. This system enhances stability and control, allowing drivers to navigate challenging environments with ease. The vehicle's suspension system is finely tuned to provide a smooth ride, even on rough roads, ensuring that cargo is transported safely and comfortably.

Safety is a paramount concern in the design of the CFM UVHB26. The vehicle is equipped with a comprehensive suite of safety technologies, including advanced braking systems, stability control, and multiple airbags. Additionally, an intuitive driver assistance system helps to enhance situational awareness, reducing the risk of accidents and ensuring a secure driving experience.

Another outstanding feature of the UVHB26 is its spacious interior and cargo capacity. The cabin is designed for comfort and functionality, with ergonomic seating arrangements that provide ample space for both drivers and passengers. The cargo area can be easily adapted to accommodate various loads, making the vehicle ideal for business use.

Incorporating modern connectivity features, the CFM UVHB26 is equipped with an infotainment system that supports smartphone integration, navigation, and communication tools. This ensures that drivers remain connected while on the move, enhancing productivity and convenience.

Overall, the CFM UVHB26 exemplifies innovation in vehicle design, combining powerful performance, safety, and technology to meet the diverse needs of its users. Whether for commercial or personal use, the UVHB26 delivers a dynamic driving experience and remains a reliable choice for those looking for a high-performance vehicle.
Top Page Image Contents