INSTALLATION STEP 6

Install the Door Control

Locate door control within sight of the door at a minimum height of 1.5 m where small children cannot reach, and away from moving parts of the door and door hardware. The installation surface must be smooth and flat. If installing into drywall (Figure 1), drill 4 mm holes and use anchors provided. For pre-wired installations (as in new home construction), it may be mounted to a single gang box (Figure 2).

NOTE: After installation, a green indicator light behind the cover will indicate proper connection. If not lit, the Lock and Light features will not function (reverse wires to correct).

1.Strip 11 mm of insulation from one end of bell wire and connect to the two screw terminals on back of door control by color: white wire to 2 and white/red wire to the 1 (Figure 3).

2.Model 1215EM - Lighted door control: Remove the cover from the Lighted Door Control. Fasten to wall with 6ABx1-1/2"self-tapping screws (Figure 4).

Model 1225EM - Multi-function door control: Remove white cover by gently prying at slot in top of the cover with a small flat head screwdriver. Fasten with 6ABx1-1/4"self-tapping screws (drywall installation) or 6-32x1" machine screws (into gang box) as follows:

• Drill and install bottom screw, allowing 3 mm to protrude above wall surface.

• Position bottom of door control on screw head and slide down to secure. Adjust screw for snug fit.

• Install top screw with care to avoid cracking plastic housing. Do not overtighten.

• Insert bottom tabs and snap on cover.

3.(Standard installation only) Run bell wire up wall and across ceiling to motor unit. Use insulated staples to secure wire in several places. Do not pierce wire with a staple, creating a short or open circuit.

4.Strip 11 mm of insulation from end of bell wire. Connect bell wire to the quick-connect terminals as follows: white to white and white/red to red (Figure 5).

NOTE: When connecting multiple door controls to the opener, twist same color wires together. Insert wires into quick-connect holes: white to white and red/white to red.

5.Use tacks or staples to permanently attach entrapment warning label to wall near door control, and manual release/safety reverse test label in a prominent location on inside of garage door.

WIRING INSTRUCTIONS FOR ACCESSORIES

The Protector System®: To opener terminals: White to White and Black to grey.

Outside Keylock Accessory connections: To opener

terminals: Red/white to Red and White to White.

To prevent possible SERIOUS INJURY or DEATH from electrocution:

•Be sure power is not connected BEFORE installing door control.

•Connect ONLY to 24 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing garage door:

•Install door control within sight of garage door, out of reach of children at a minimum height of 1.5 m, and away from ALL moving parts of door.

•NEVER permit children to operate or play with door control push buttons or remote control transmitters.

•Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

•ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.

HARDWARE SHOWN ACTUAL SIZE

 

 

 

 

Lighted Door Control Button

 

 

 

 

 

 

 

 

 

 

Insulated

 

 

 

 

 

6ABx1-1/2" Screw

 

 

 

 

 

 

 

 

 

 

 

Staples

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Drywall

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Multi-function (std installation)

Multi-function (pre-wired)

 

 

6AB x 1-1/4" Screw

 

6-32 x 1" Screw

Anchors

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STANDARD

 

 

 

 

 

 

 

 

 

 

PRE-WIRED

 

Figure 1 INSTALLATION

Figure 2 INSTALLATION

 

Single

Gang Box

LOCK

 

 

 

LIGHT

 

LOCK

 

 

 

 

To Replace

 

LIGHT

 

 

 

24 Volt

Insert Bottom Tabs First

To Replace

Bell Wire

 

Insert Bottom Tabs First

 

 

Figure 3 DOOR CONTROL (BACK)

Figure 4 REMOVE COVER

Top Mounting Hole

 

 

Terminal

 

 

 

Screws

 

 

 

WHT

 

 

 

-2

 

 

 

RED WHT

 

 

1

2

 

 

RED

 

 

 

-1

 

 

 

Bell Wire

Bottom Mounting Hole

Figure 5

 

Door Control

 

To release or insert wire,

 

Connections

 

push in tab with screwdriver tip

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Red White Grey

11 mm

Strip wire 11 mm

22