Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain 1215EM FS2 Planning (Continued), ONE-PIECEDOOR WITH TRACK, ONE-PIECEDOOR INSTALLATIONS, ONE-PIECEDOOR WITHOUT TRACK

1 80

Download 80 pages, 3.61 Mb

Planning (Continued)ONE-PIECE DOOR INSTALLATIONS

•Generally, a one-piece door does not require reinforcement. If your door is lightweight, refer to the information relating to sectional doors in Installation Step 10.

•Depending on your door’s construction, you may need additional mounting hardware for the door bracket (Step 10).

Without a properly working safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.

•The gap between the bottom of the garage door and the floor MUST NOT exceed 6 mm. Otherwise, the safety reversal system may not work properly.

•The floor or the garage door MUST be repaired to eliminate the gap.

ONE-PIECE DOOR WITHOUT TRACK

Slack in Chain Tension is Normal When Garage Door is Closed

Header

Wall

FINISHED CEILING Support bracket

&fastening hardware is required. See page 21.

Motor Unit

	Gap between floor and bottom
Safety	of door must not exceed 6 mm.

Reversing Sensor

(Optional Accessory)

Wall-mounted

Door

Control

Access

Door

Safety

Reversing Sensor

(Optional Accessory)

CLOSED POSITION

	Header	Chain
	Bracket	Pulley	Chain
		Bracket Trolley	Chain
	Garage
	Door
	Spring		Manual
		Straight	Release
		Straight	Rope & Handle
		Door
		Arm
		Curved
Header		Door
Header		Arm
Wall		Arm
Wall	Door Bracket
Garage
Door

ONE-PIECE DOOR WITH TRACK

CLOSED POSITION

Safety Reversing

Sensor

(Optional Accessory)

Gap between floor and bottom of door must not exceed 6 mm

Access

Door

Wall-

Mounted

Door

Control

Safety Reversing

Sensor

(Optional Accessory)

	Cable	Trolley	Chain
Header	Pulley Bracket
Header
Wall
	Header	Curved	Rail
	Bracket	Door Arm	Rail
Garage	Door	Straight
	Door	Door
	Bracket
Door
		Arm


		Emergency Release
		Rope & Handle

5

Contents

■Please read this manual and the enclosed safety materials carefully ■Fasten the manual near the garage door after installation ■Periodic checks of the opener are required to ensure safe operation ■The model number label is located on the front panel of your opener Mechanical Electrical Preparing your garage door Complete the following test Sectional Door One-PieceDoor Tools needed Planning SECTIONAL DOOR INSTALLATIONS SECTIONAL DOOR INSTALLATION Planning (Continued) ONE-PIECEDOOR INSTALLATIONS ONE-PIECEDOOR WITHOUT TRACK ONE-PIECEDOOR WITH TRACK GATE INSTALLATIONS SLIDING GATE INSTALLATION SWINGING GATE INSTALLATION Carton Inventory Assembly Hardware 41A3534 Installation Hardware 41A3535 ASSEMBLY STEP For Sectional and One-PieceDoors ONLY Assemble the Rail and Attach the Chain Pulley Bracket For Sliding and Swinging Gates ONLY Assemble the Rail and Attach the Chain Pulley Bracket For Sectional and One-PieceDoors Only Install the Trolley For Sliding and Swinging Gates Only Install the Trolley Fasten the Rail to the Motor Unit Remember to use only these bolts! Any other bolts will cause serious damage to the opener Model 1225EM Only: For Sectional and One-PieceDoors Only Install the Chain and Attach the Sprocket Cover INSTALLING THE CHAIN Figure For Sliding and Swinging Gates Only Tighten the Chain Sprocket noise can result if chain is either too loose or too tight INSTALLATION INSTALLATION STEP Determine the Header Bracket Location SECTIONAL DOOR AND ONE-PIECEDOOR WITH TRACK You can fasten the header bracket within 1.2 m of EXAMPLE One-piecedoor without track: jamb hardware One-piecedoor without track: pivot hardware Install the Header Bracket WALL HEADER BRACKET INSTALLATION CEILING HEADER BRACKET INSTALLATION Attach the Rail to the Header Bracket Position the Opener SECTIONAL DOOR OR ONE-PIECEDOOR WITH TRACK Hang the Opener Install the Door Control Model 1215EM - Lighted door control: Do not overtighten (Standard installation only) WIRING INSTRUCTIONS FOR ACCESSORIES Install the Lights Attach the Emergency Release Rope and Handle Optional installation: Electrical Requirements To avoid installation difficulties, do not run the opener at this time The opener must be grounded Fasten the Door Bracket SECTIONAL DOORS ONE-PIECEDOORS Connect Door Arm to Trolley SECTIONAL DOORS ONLY Figure 1: Figure 2: • Figure 3, Hole alignment alternative: ALL ONE-PIECEDOORS 1.Assemble the door arm: 2.Adjustment procedures: •Open door adjustment: decrease UP travel limit •Closed door adjustment: decrease DOWN travel limit ADJUSTMENT STEP Adjust the UP and DOWN Travel Limits Run the opener through a complete travel cycle after each adjustment HOW AND WHEN TO ADJUST THE LIMITS •If the door does not open completely but opens at least 1.5 m: Adjust the Force HOW AND WHEN TO ADJUST THE FORCES 1. Test the DOWN (close) force 2.Test the UP (open) force If the door is hard to hold or doesn't stop Test the Safety Reversal System Garage Door Installation must Gate Installation OPERATION Using Your Garage Door Opener The opener lights Activate your opener with any of the following: Timer to close feature (ONLY available when optional Using the Wall-MountedDoor Control THE LIGHTED DOOR CONTROL BUTTON (MODEL 1215EM) THE MULTI-FUNCTIONDOOR CONTROL (MODEL 1225EM) Light feature To Open the Door Manually Care of Your Opener Having a Problem LIMIT AND FORCE ADJUSTMENTS MAINTENANCE SCHEDULE Once a Month Having a Problem? (Continued) 7. The door doesn't open completely: 8. The door stops but doesn't close completely: 9.The door reverses for no apparent reason and opener lights don’t blink: 10. The opener lights don't turn on: PROGRAMMING NOTICE: To Add or Reprogram a Hand-heldRemote Control USING THE LIGHTED DOOR CONTROL USING THE MULTI-FUNCTIONDOOR CONTROL To Add, Reprogram or Change a Keyless Entry PIN To change an existing, known PIN To set a temporary PIN hours times Motor Unit Assembly Parts KEY PART DESCRIPTION ACCESSORIES 970LM 3-Button Mini-RemoteControl with 1702E Security✚®: TEL.: 630-516-8423Worldwide in USA FAX: 630-993-6916Worldwide in USA TEL.: 5333-9974In Mexico City TEL.: 01-800-500-9300Toll Free in Mexico LIFTMASTER GARAGE DOOR OPENER ONE-YEARLIMITED WARRANTY Sólo para uso residencial CONTENIDO Introducción Ensamblado Instalación Ajustes Preparación de la puerta del garaje Herramientas necesarias Planificación Planificación (continuación) Page Inventario de las cajas Pernería de Ensamble 41A3534 Pernería de Instalacion 41A3535 ENSAMBLADO PASO SOLO para puertas seccionales y de una sola pieza Ensamble de riel con soporte de catarina SOLO para puertas corredizas y batientes Ensamble Riel con Soporte de Catarina Solamente para puertas seccionales y de una sola pieza con rieles Instalar el carro sobre el riel Sólamente para puertas corredizas y batientes Fijar riel al abre-puertasde garaje Instalar la cadena y conectar la cubierta del portacadena Page Apretar la cadena INSTALACIÓN INSTALACIÓN PASO Determinar la localización de soporte de cabecera EJEMPLO Instale la ménsula del cabezal Coloque el riel en la ménsula del cabezal Coloque el abre-puertas Cuelgue el abre-puertas Instalar el control de la puerta Instalación del bombilla Montaje de la manija y la cuerda de emergencia Requisitos para la instalación eléctrica Sujete la ménsula de la puerta Page Conectar el brazo de la puerta al carro Page AJUSTES, PASO Ajuste el límite del recorrido hacia arriba y hacia abajo Ajuste la fuerza Pruebe el sistema de reversa de seguridad Instalación del abre-puertasde garaje Instalación del puertas OPERACIÓN 15.CONSERVE ESTAS INSTRUCCIONES Cómo usar su abre-puertasde garaje Cómo usar la unidad de control de pared Para abrir la puerta manualmente Mantenimiento de su abre-puertasde garaje ¿Si tiene algún problema Si tiene algún problema (continuación) PROGRAMACIÓN Cómo Agregar o Reprogramar un Control Remoto Para borrar todos los códigos de la memoria de la unidad del motor *Controles remotos 3 botones Agragar, Reprogramar o Cambiar un Código de la Llave Digital Piezas de la unidad del motor ACCESORIOS 760E 99E