INSTALLATION STEP 6

Install the Door Control

Locate door control within sight of door, at a minimum height of 5 feet (1.5 m) where small children cannot reach, away from moving parts of door and door hardware.

If installing into drywall, drill 5/32" holes and use the anchors provided. For pre-wired installations (as in new home construction), it may be mounted to a single gang box (Figure 2).

NOTE: The functional temperature range of the door control is between -4° F (-20° C) and 122° F (50° C). Scroll speed of display is slower at lower temperatures although the door control remains fully functional.

CAUTION: Continuous exposure of the door control to temperatures below -22° F (-30° C) may damage the LCD screen.

1.Strip 7/16" (11 mm) of insulation from one end of bell wire and connect to the two screw terminals on back of door control by color: white wire to W (2) and white/red wire to the R (1).

2.Remove cover by gently prying at slot in top of the cover with a small flat head screwdriver. Fasten with 6ABx1-1/4" self-tapping screws (drywall installation) or

6-32x1" machine screws (into gang box) as follows:

•Install bottom screw, allowing 1/8" (3 mm) to protrude above wall surface.

•Position bottom of door control on screw head and slide down to secure. Adjust screw for snug fit.

•Drill and install top screw with care to avoid cracking plastic housing. DO NOT overtighten.

•Insert top tabs and snap on cover.

3.(For standard installation only) Run bell wire up wall and across ceiling to motor unit. Use insulated staples to secure wire in several places. DO NOT pierce wire with a staple, creating a short or open circuit.

4.Strip 7/16" (11 mm) of insulation from end of bell wire. Connect bell wire to the quick-connect terminals as follows: white to white and white/red to red.

5.Position the antenna wire as shown.

6.Use tacks or staples to permanently attach entrapment warning label to wall near door control, and manual release/safety reverse test label in a prominent location on inside of garage door.

NOTE: DO NOT connect power and operate opener at

this time. The trolley will travel to the full open position but will not return to the close position until the sensor beam is connected and properly aligned.

To prevent possible SERIOUS INJURY or DEATH from electrocution:

•Disconnect ALL electric and battery power BEFORE performing ANY service or maintenance.

•Connect ONLY to 24 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing garage door:

•Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door.

•NEVER permit children to operate or play with door control push buttons or remote controls.

•Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

•ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.

Outside Keylock Accessory Connections

To opener quick-connect terminals: white to white; white/red to red.

HARDWARE SHOWN ACTUAL SIZE

Screw 6ABx1-1/4"

Insulated Staples

(standard installation)

 

Screw 6-32x1" (pre-wired)

Drywall Anchors

Figure 1

Figure 2

REMOVE & REPLACE COVER

PRE-WIRED

To Replace

INSTALLATION

 

Insert Top

 

Tabs First

 

Push Bar

24 Volt

Cover

Bell Wire

 

Top

Door Control Connections

To insert or release wire, push

 

Mounting

in tab with screwdriver tip

 

 

 

Hole

Strip wire 7/16" (11 mm)

 

 

Terminal

 

 

 

 

 

Screws

 

 

Bell

Bottom

 

 

Mounting

 

 

Wire

 

Red White Grey

Hole

 

(BACK VIEW)

 

17