Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain 459950, 547445, HD900CD Planning (Continued), ONE-PIECEDOOR WITH TRACK, ONE-PIECEDOOR INSTALLATIONS, ONE-PIECEDOOR WITHOUT TRACK

1 88

Download 88 pages, 5.77 Mb

Planning (Continued)

ONE-PIECE DOOR INSTALLATIONS

•Generally, a one-piece door does not require reinforcement. If your door is lightweight, refer to the information relating to sectional doors in Installation Step 12.

•Depending on your door’s construction, you may need additional mounting hardware for the door bracket (Step 12).

Without a properly working safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door.

•The gap between the bottom of the garage door and the ﬂoor MUST NOT exceed 1/4" (6 mm). Otherwise, the safety reversal system may NOT work properly.

•The ﬂoor or the garage door MUST be repaired to eliminate the gap.

ONE-PIECE DOOR WITHOUT TRACK

Safety Reversing Sensor

FINISHED CEILING

Support bracket & fastening hardware is required.

See page 16.

Rail

Header Wall

Wall-mounted

Door Control

Access

Door

Safety Reversing Sensor Gap between ﬂoor and

bottom of door must not exceed 1/4" (6 mm).

Motor unit

			CLOSED POSITION
	Trolley Stop Bolt Belt		Trolley
	Header	Rail
	Bracket	Rail
	Door Bracket			Emergency
				Release
		Straight	Curved	Rope &
			Curved	Handle
			Door	Handle
		Door Arm	Door
		Door Arm	Arm
Header	Garage		Arm
Header	Garage
Wall	Door

ONE-PIECE DOOR WITH TRACK

Safety

Reversing

Sensor

Access

Door

Safety

Reversing

Gap between ﬂoor Sensor and bottom of door

must not exceed 1/4" (6 mm).

			CLOSED POSITION
		Trolley Stop Bolt		Belt	Trolley
		Header	Curved
		Bracket	Door Arm		Rail
		Door			Emergency
		Bracket		Straight	Release
	Header	Garage		Door	Rope &
	Header	Garage		Arm	Handle
	Wall	Door		Arm	Handle
	Wall	Door

5

Contents

For Residential Use Only Introduction Assembly Installation Adjustment Operation Preparing Your Garage Door Tools needed Planning Planning (Continued) Carton Inventory Hardware Inventory Assemble the Rail & Install the Trolley Fasten the Rail to the Motor Unit Install the Idler Pulley Install the Belt and Attach the Belt Cap Retainer WARNING Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Battery Install the Lights Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation (Figures 2 and 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY REVERSING SENSORS Mounting: Option A - Installation Without Pre-Wiring: Option B - Pre-WiredInstallation: Connect to garage door opener: ALIGNING THE SAFETY REVERSING SENSORS TROUBLESHOOTING THE SAFETY Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to the Trolley ALL ONE-PIECEDOORS 1. Assemble the Door Arm Program the Travel Limits Set the Force Test the Safety Reversal System Test The Protector System® IMPORTANT SAFETY INSTRUCTIONS Using Your Garage Door Opener Using the Wall-MountedDoor Control Standby Power Unit (Optional) To Open the Door Manually Care of Your Opener Having a Problem? (Troubleshooting) Diagnostic Chart 1 FLASH 2 FLASHES 3 FLASHES 4 FLASHES Smart Control Panel® Messages Message To Add or Reprogram a Hand-HeldRemote Control To Erase All Codes From Motor Unit Memory *3-ButtonRemotes (315 MHz) To Add, Reprogram or Change a Keyless Entry PIN Rail Assembly Parts Motor Unit Assembly Parts ACCESSORIES 7702COutside Quick Release: 8808C 8 Foot (2.4 m) Rail Extension: 8810C Page OUR LARGE SERVICE ORGANIZATION SPANS AMERICA AND CANADA www.chamberlain.com For professional installation, parts and service WHEN ORDERING REPAIR PARTS, ALWAYS GIVE Pour Résidences Seulement TABLE DES MATIÈRES Introduction Montage Pose Réglages Préparation de votre porte de garage Outils nécessaires Planiﬁcation Planiﬁcation (Suite) Inventaire de la boîte d’emballage Inventaire des ﬁxations MONTAGE - 1re OPÉRATION Montage du rail et pose du chariot MONTAGE - 2e OPÉRATION Fixation du rail sur le moteur MONTAGE - 3e OPÉRATION Pose de la poulie MONTAGE - 4e OPÉRATION Pose de la courroie et ﬁxation du capuchon de retenue de la courroie MONTAGE - 5e OPÉRATION Régler la tension POSE LA POSE ou MORTELLES : POSE – 1re OPÉRATION POSE - 2e OPÉRATION Pose du support de linteau POSE - 3e OPÉRATION Fixation du rail sur le support de linteau POSE - 4e OPÉRATION Positionnement de l'ouvre-porte POSE - 5e OPÉRATION Accrochage de l'ouvre-porte POSE - 6e OPÉRATION Pose de la commande de porte POSE - 7e OPÉRATION Pose de batterie de secours POSE - 8e OPÉRATION Pose des ampoules POSE - 9e OPÉRATION POSE - 10e OPÉRATION Exigences électriques POSE - 11e OPÉRATION Pose du Système Protector® POSE DES SUPPORTS Pose murale (Figures 2 et 3) : Pose au sol (Figure 4) : MONTAGE ET CÂBLAGE DES DÉTECTEURS INVERSEURS DU SECURITIÉ Montage : Option A - Installation sans les câbles préinstallés : Option B - Installation pré-câblée : Connexion à l’ouvre-portede garage : POSE - 12e OPÉRATION Fixation du support de la porte PORTES RIGIDES POSE - 13e OPÉRATION Fixation de la biellette de la porte au chariot POUR TOUTES LES PORTES RIGIDES 1. Assemblage des biellettes : RÉGLAGES – 1re OPÉRATION Programmation des limites de la course RÉGLAGES – 2e OPÉRATION Réglage de sensibilité RÉGLAGES - 3e OPÉRATION Contrôle du système d’inversion de sécurité RÉGLAGES - 4e OPÉRATION Essai du Systéme Protector® FONCTIONNEMENT ou DE MORT :