Manuals / Brands / Household Appliance / Garage Door Opener / Chamberlain / Household Appliance / Garage Door Opener

Chamberlain 459950, 547445, HD900CD Install the Header Bracket, WALL HEADER BRACKET INSTALLATION, CEILING HEADER BRACKET INSTALLATION

1 88

Download 88 pages, 5.77 Mb

INSTALLATION STEP 2

Install the Header Bracket

You can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry, use concrete anchors (not provided).

WALL HEADER BRACKET INSTALLATION

•Center the bracket on the vertical centerline with the bottom edge of the bracket on the horizontal line as shown (with the arrow pointing toward the ceiling).

Wall Mount

Optional

Mounting Holes

•Mark the vertical set of bracket holes. Drill 3/16" pilot holes and fasten the bracket securely to a structural support with the hardware provided.

HARDWARE SHOWN ACTUAL SIZE

Lag Screw 5/16"-9x1-5/8"

	Vertical
- Header Wall -	Centerline
	of Garage
2x4	Door
Structural
Support	Header
	Bracket

Lag Screws 5/16"-9x1-5/8"

Horizontal
Line	Door Spring

	Highest Point of	- Garage Door -
	Highest Point of
CEILING HEADER BRACKET INSTALLATION	Garage Door Travel	Vertical
CEILING HEADER BRACKET INSTALLATION		Centerline
• Extend the vertical centerline onto the ceiling as shown.		of Garage Door
• Extend the vertical centerline onto the ceiling as shown.
• Center the bracket on the vertical mark, no more than
6" (15 cm) from the wall. Make sure the arrow is
pointing away from the wall. The bracket can be
mounted ﬂush against the ceiling when clearance
is minimal.
• Mark the side holes. Drill 3/16" pilot holes and fasten
bracket securely to a structural support with the		- Finished Ceiling -
hardware provided.		Vertical Centerline
		Vertical Centerline
		of Garage Door
	Header
	Bracket
	6" (15 cm) Maximum
Ceiling Mounting Holes	Door	Lag Screws
	Spring	Lag Screws
		5/16"-9x1-5/8"
		- Header Wall -
	Garage Door	Vertical
		Vertical
		Centerline
		of Garage Door

13

Contents

For Residential Use Only Introduction Assembly Installation Adjustment Operation Preparing Your Garage Door Tools needed Planning Planning (Continued) Carton Inventory Hardware Inventory Assemble the Rail & Install the Trolley Fasten the Rail to the Motor Unit Install the Idler Pulley Install the Belt and Attach the Belt Cap Retainer WARNING Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Battery Install the Lights Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation (Figures 2 and 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY REVERSING SENSORS Mounting: Option A - Installation Without Pre-Wiring: Option B - Pre-WiredInstallation: Connect to garage door opener: ALIGNING THE SAFETY REVERSING SENSORS TROUBLESHOOTING THE SAFETY Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to the Trolley ALL ONE-PIECEDOORS 1. Assemble the Door Arm Program the Travel Limits Set the Force Test the Safety Reversal System Test The Protector System® IMPORTANT SAFETY INSTRUCTIONS Using Your Garage Door Opener Using the Wall-MountedDoor Control Standby Power Unit (Optional) To Open the Door Manually Care of Your Opener Having a Problem? (Troubleshooting) Diagnostic Chart 1 FLASH 2 FLASHES 3 FLASHES 4 FLASHES Smart Control Panel® Messages Message To Add or Reprogram a Hand-HeldRemote Control To Erase All Codes From Motor Unit Memory *3-ButtonRemotes (315 MHz) To Add, Reprogram or Change a Keyless Entry PIN Rail Assembly Parts Motor Unit Assembly Parts ACCESSORIES 7702COutside Quick Release: 8808C 8 Foot (2.4 m) Rail Extension: 8810C Page OUR LARGE SERVICE ORGANIZATION SPANS AMERICA AND CANADA www.chamberlain.com For professional installation, parts and service WHEN ORDERING REPAIR PARTS, ALWAYS GIVE Pour Résidences Seulement TABLE DES MATIÈRES Introduction Montage Pose Réglages Préparation de votre porte de garage Outils nécessaires Planiﬁcation Planiﬁcation (Suite) Inventaire de la boîte d’emballage Inventaire des ﬁxations MONTAGE - 1re OPÉRATION Montage du rail et pose du chariot MONTAGE - 2e OPÉRATION Fixation du rail sur le moteur MONTAGE - 3e OPÉRATION Pose de la poulie MONTAGE - 4e OPÉRATION Pose de la courroie et ﬁxation du capuchon de retenue de la courroie MONTAGE - 5e OPÉRATION Régler la tension POSE LA POSE ou MORTELLES : POSE – 1re OPÉRATION POSE - 2e OPÉRATION Pose du support de linteau POSE - 3e OPÉRATION Fixation du rail sur le support de linteau POSE - 4e OPÉRATION Positionnement de l'ouvre-porte POSE - 5e OPÉRATION Accrochage de l'ouvre-porte POSE - 6e OPÉRATION Pose de la commande de porte POSE - 7e OPÉRATION Pose de batterie de secours POSE - 8e OPÉRATION Pose des ampoules POSE - 9e OPÉRATION POSE - 10e OPÉRATION Exigences électriques POSE - 11e OPÉRATION Pose du Système Protector® POSE DES SUPPORTS Pose murale (Figures 2 et 3) : Pose au sol (Figure 4) : MONTAGE ET CÂBLAGE DES DÉTECTEURS INVERSEURS DU SECURITIÉ Montage : Option A - Installation sans les câbles préinstallés : Option B - Installation pré-câblée : Connexion à l’ouvre-portede garage : POSE - 12e OPÉRATION Fixation du support de la porte PORTES RIGIDES POSE - 13e OPÉRATION Fixation de la biellette de la porte au chariot POUR TOUTES LES PORTES RIGIDES 1. Assemblage des biellettes : RÉGLAGES – 1re OPÉRATION Programmation des limites de la course RÉGLAGES – 2e OPÉRATION Réglage de sensibilité RÉGLAGES - 3e OPÉRATION Contrôle du système d’inversion de sécurité RÉGLAGES - 4e OPÉRATION Essai du Systéme Protector® FONCTIONNEMENT ou DE MORT :