Chamberlain 459950, 547445, HD900CD Carton Inventory

Carton Inventory

Your garage door opener is packaged in one carton which contains the motor unit and all parts illustrated below. Accessories will depend on the model purchased. If anything is missing, carefully check the packing material.

Parts may be stuck in the foam. Hardware for assembly and installation is shown on the next page. Save the carton and packing material until installation and adjustment is complete.

	Motor Unit with 2 Light Lenses		Belt Cap Retainer
	Motor Unit with 2 Light Lenses	Battery	Belt
		Battery	Belt
			Safety Labels
			and
	The Protector System®		Literature
	(2) Safety Reversing Sensors		2-Conductor Bell Wire
	(1 Sending Eye and 1 Receiving Eye)	Safety Reversing	2-Conductor Bell Wire
	with 2-Conductor White & White/Black	Safety Reversing	White & White/Red
	with 2-Conductor White & White/Black	Sensor Bracket (2)	White & White/Red
	Bell Wire attached	Sensor Bracket (2)
	Bell Wire attached

	Trolley
Door Bracket
	Header Bracket
Hanging Brackets
	Rail Center/Back
“U” Bracket	Sections

Smart Control Panel®

Curved Door

Arm Section

SECURITY✚® 3-Button

Straight DoorRemote Control (2)

Arm Section

SECURITY✚®

Keyless Entry

		SECURITY✚® 3-Button
		Mini-Remote Control (1)
Idler Pulley	Remote Light Control	Model 547445 Only

Rail Front

(header) Section

Garage Door Monitor	Park Assist	Surge Protector
Model 547445 Only	Model 547445 Only	Model 547445 Only

6

Contents

For Residential Use Only Introduction Assembly Installation Adjustment Operation Preparing Your Garage Door Tools needed Planning Planning (Continued) Carton Inventory Hardware Inventory Assemble the Rail & Install the Trolley Fasten the Rail to the Motor Unit Install the Idler Pulley Install the Belt and Attach the Belt Cap Retainer WARNING Determine the Header Bracket Location Install the Header Bracket Attach the Rail to the Header Bracket Position the Opener Hang the Opener Install the Door Control Install the Battery Install the Lights Attach the Emergency Release Rope and Handle Electrical Requirements Install The Protector System® INSTALLING THE BRACKETS Garage door track installation (preferred): Wall installation (Figures 2 and 3): Floor installation (Figure 4): MOUNTING AND WIRING THE SAFETY REVERSING SENSORS Mounting: Option A - Installation Without Pre-Wiring: Option B - Pre-WiredInstallation: Connect to garage door opener: ALIGNING THE SAFETY REVERSING SENSORS TROUBLESHOOTING THE SAFETY Fasten the Door Bracket ONE-PIECEDOORS Metal Doors: Connect Door Arm to the Trolley ALL ONE-PIECEDOORS 1. Assemble the Door Arm Program the Travel Limits Set the Force Test the Safety Reversal System Test The Protector System® IMPORTANT SAFETY INSTRUCTIONS Using Your Garage Door Opener Using the Wall-MountedDoor Control Standby Power Unit (Optional) To Open the Door Manually Care of Your Opener Having a Problem? (Troubleshooting) Diagnostic Chart 1 FLASH 2 FLASHES 3 FLASHES 4 FLASHES Smart Control Panel® Messages Message To Add or Reprogram a Hand-HeldRemote Control To Erase All Codes From Motor Unit Memory *3-ButtonRemotes (315 MHz) To Add, Reprogram or Change a Keyless Entry PIN Rail Assembly Parts Motor Unit Assembly Parts ACCESSORIES 7702COutside Quick Release: 8808C 8 Foot (2.4 m) Rail Extension: 8810C Page OUR LARGE SERVICE ORGANIZATION SPANS AMERICA AND CANADA www.chamberlain.com For professional installation, parts and service WHEN ORDERING REPAIR PARTS, ALWAYS GIVE Pour Résidences Seulement TABLE DES MATIÈRES Introduction Montage Pose Réglages Préparation de votre porte de garage Outils nécessaires Planiﬁcation Planiﬁcation (Suite) Inventaire de la boîte d’emballage Inventaire des ﬁxations MONTAGE - 1re OPÉRATION Montage du rail et pose du chariot MONTAGE - 2e OPÉRATION Fixation du rail sur le moteur MONTAGE - 3e OPÉRATION Pose de la poulie MONTAGE - 4e OPÉRATION Pose de la courroie et ﬁxation du capuchon de retenue de la courroie MONTAGE - 5e OPÉRATION Régler la tension POSE LA POSE ou MORTELLES : POSE – 1re OPÉRATION POSE - 2e OPÉRATION Pose du support de linteau POSE - 3e OPÉRATION Fixation du rail sur le support de linteau POSE - 4e OPÉRATION Positionnement de l'ouvre-porte POSE - 5e OPÉRATION Accrochage de l'ouvre-porte POSE - 6e OPÉRATION Pose de la commande de porte POSE - 7e OPÉRATION Pose de batterie de secours POSE - 8e OPÉRATION Pose des ampoules POSE - 9e OPÉRATION POSE - 10e OPÉRATION Exigences électriques POSE - 11e OPÉRATION Pose du Système Protector® POSE DES SUPPORTS Pose murale (Figures 2 et 3) : Pose au sol (Figure 4) : MONTAGE ET CÂBLAGE DES DÉTECTEURS INVERSEURS DU SECURITIÉ Montage : Option A - Installation sans les câbles préinstallés : Option B - Installation pré-câblée : Connexion à l’ouvre-portede garage : POSE - 12e OPÉRATION Fixation du support de la porte PORTES RIGIDES POSE - 13e OPÉRATION Fixation de la biellette de la porte au chariot POUR TOUTES LES PORTES RIGIDES 1. Assemblage des biellettes : RÉGLAGES – 1re OPÉRATION Programmation des limites de la course RÉGLAGES – 2e OPÉRATION Réglage de sensibilité RÉGLAGES - 3e OPÉRATION Contrôle du système d’inversion de sécurité RÉGLAGES - 4e OPÉRATION Essai du Systéme Protector® FONCTIONNEMENT ou DE MORT :