TROUBLESHOOTING
Continued
OBSERVED PROBLEM | POSSIBLE CAUSE | REMEDY | ||
|
|
|
| |
ODS/pilot lights but flame | 1. Control knob not fully pressed in | 1. | Press in control knob fully | |
goes out when control knob is | 2. Control knob not pressed in | 2. | After ODS/pilot lights, keep | |
released |
| long enough |
| control knob pressed in 30 |
| 3. | Equipment shutoff valve not |
| seconds |
| 3. | Fully open equipment shutoff | ||
|
| fully open |
| valve |
| 4. | Pilot flame not touching | 4. | A) Contact local natural or |
|
| thermocouple, which allows |
| propane/LP gas company |
|
| thermocouple to cool, caus- |
|
|
|
| ing pilot flame to go out. This |
| B) Clean ODS/pilot (see |
|
| problem could be caused by |
| Cleaning and Maintenance, |
|
| one or both of the following: |
| page 23) or replace ODS/pilot |
|
| A) Low gas pressure |
| assembly |
|
| B) Dirty or partially clogged |
|
|
|
| ODS/pilot |
|
|
| 5. | Thermocouple connection | 5. | Hand tighten until snug, then |
|
| loose at control valve |
| tighten 1/4 turn more |
| 6. | Thermocouple damaged | 6. | Replace pilot assembly |
| 7. | Control valve damaged | 7. | Replace control valve |
|
|
|
| |
Burners does not light after | 1. Inlet gas pressure is too low | 1. | Contact local natural or pro- | |
ODS/pilot is lit | 2. | Burner orifice(s) clogged |
| pane/LP gas company |
| 2. | Clean burner(s) (see Cleaning | ||
|
|
|
| and Maintenance, page 23) or |
| 3. | Thermopile leads disconnect- |
| replace burner orifice(s) |
| 3. | Reconnect leads (see Wiring | ||
|
| ed or improperly connected |
| Diagram, page 24) |
| 4. | Burner will not come on in | 4. | Replace battery in transmitter |
|
| remote position |
| and receiver |
|
|
|
| |
Delayed ignition of one or both | 1. Manifold pressure is too low | 1. | Contact local natural or pro- | |
burners | 2. | Burner orifice(s) clogged |
| pane/LP gas company |
| 2. | Clean burner(s) (see Cleaning | ||
|
|
|
| and Maintenance, page 23) or |
|
|
|
| replace burner orifice(s) |
|
|
|
| |
Burner backfiring during com- | 1. Burner orifice is clogged or | 1. | Clean burner (see Cleaning | |
bustion |
| damaged |
| and Maintenance, page 23) or |
|
|
|
| replace burner orifice(s) |
| 2. | Damaged burner | 2. | Replace damaged burner |
| 3. | Gas regulator defective | 3. | Replace gas regulator |
|
|
|
| |
Slight smoke or odor during | 1. Not enough air | 1. | Check burner for dirt and | |
initial operation |
|
|
| debris. If found, clean burner |
|
|
|
| (see Cleaning and Mainte- |
| 2. | Gas regulator defective |
| nance, page 23) |
| 2. | Replace gas control | ||
| 3. | Residues from manufacturing | 3. | Problem will stop after a few |
|
| processes and logs curing |
| hours of operation |
26 | www.desatech.com |
