Using the Wall-Mounted Door Control

THE SMART CONTROL PANEL®
(Prog) Learn Feature

Press the push button to open or close the door. Press again to reverse the door during the closing cycle or to stop the door while it’s opening.

Motion Sensing

 

ON/OFF

Push

 

Prog <LEARN>

Bar

 

Hour

 

Minute

Light

Language

Degrees (F/C)

Button

 

 

Lock

 

Button

The door control is equipped with a Prog <LEARN> button to assist in learning remote controls to the unit. Press the Prog <LEARN> button once to initiate LEARN mode and the display will show ‘Learn Remote Control - Press Learn Button Again to Confirm’. Press the Prog <LEARN> button a second time and the display will show ‘Learn Mode - Press Remote Control Button to Learn Remote.’ Press the button of the remote control to be learned and the worklight will blink to confirm the remote control has been learned.

This door control contains a motion detector that will automatically turn on the light when it detects a person entering the garage. This feature can be easily turned off for extended work light use.

Light Feature

Press the Light button to turn the opener light

LIGHT on or off. It will not control the opener lights when the door is in motion. If you turn it on and

then activate the opener, the light will remain on for 4-1/2 minutes. Press again to turn it off sooner. The 4-1/2 minute interval can be changed to 1-1/2, 2-1/2 or 3-1/2 minutes as follows: Press and hold the Lock button until the light blinks (about 10 seconds). A single blink indicates that the timer is reset to 1-1/2 minutes. Repeat the procedure and the light will blink twice, resetting the timer to 2-1/2 minutes. Repeat again for a 3-1/2 minute interval, etc., up to a maximum of four blinks and 4-1/2 minutes.

When using the opener lights as working lights, we recommend that you first disable the motion sensor.

Lock Feature

Designed to prevent operation of the door from

LOCK hand-held remote controls. However, the door will open and close from the Door Control, the Outside

Keylock and the Keyless Entry Accessories.

To activate, press and hold the Lock button for 2 seconds.

To turn off, press and hold the Lock button again for

2 seconds. The Lock feature will also turn off whenever the “learn” button on the motor unit panel is activated.

Motion Detecting Light Feature

The opener light will turn on automatically when a person walks in front of the wall-mounted door control. This feature works by detecting motion and body heat and may not work in temperatures around 100˚ F (37.7˚ C). The opener light will come on for 5 minutes, then shut off automatically if no additional motion or heat differential is calculated. To disable this feature, press the Motion Detecting Light On/Off button on the left side of the door control.

We recommend that you disable the motion sensor when using the opener lights as working lights. Otherwise, they will turn off automatically if you are working beyond the sensor’s range.

 

 

 

 

 

 

 

Hour & Minute Feature

H

 

 

 

 

 

M

Press or hold either of these side

 

 

 

 

 

 

 

 

 

 

 

 

 

 

buttons to increment the hour or minute

 

 

 

 

 

 

 

 

 

 

 

 

 

 

displayed on the LCD display.

(Lang) Language Feature

Press this side button to toggle between the three languages - English, Spanish, and French.

Degrees F/C Feature

Press this side button to toggle the temperature units between Fahrenheit and Celsius.

Additional feature when used with the 3-Button hand-held remote

To control the opener lights:

In addition to operating the door, you may program the remote to operate the lights.

1.With the door closed, press and hold a small remote button that you want to control the light.

2.Press and hold the Light button on the door control.

3.While holding the Light button, press and hold the Lock button on the door control.

4.After the opener lights flash, release all buttons.

32