Cino F700BT Enable, Reserved ASCII 0 –

Reference Manual

Wireless FuzzyScan

Appendix

Keyboard Function Code Table

No.	ANSI	ASCII	Key Function	No.	ANSI	ASCII	Key Function

00	NUL	00H	RESERVED	16	DLE	10H	F7

01	SOH	01H	CTRL (Left)	17	DC1	11H	F8

02	STX	02H	ALT (Left)	18	DC2	12H	F9

03	ETX	03H	SHIFT	19	DC3	13H	F10

04	EOT	04H	CAPS LOCK	20	DC4	14H	F11

05	ENQ	05H	NUM LOCK	21	NAK	15H	F12

06	ACK	06H	ESC	22	SYN	16H	INS (Insert) (Edit)

07	BEL	07H	F1	23	ETB	17H	DEL (Delete) (Edit)

08	BS	08H	BACK SPACE	24	CAN	18H	HOME (Edit)

09	HT	09H	TAB	25	EM	19H	END (Edit)

10	LF	0AH	F2	26	SUB	1AH	PAGE UP (Edit)

11	VT	0BH	F3	27	ESC	1BH	PAGE DOWN (Edit)

12	FF	0CH	F4	28	FS	1CH	UP (Edit)

13	CR	0DH	ENTER (CR)	29	GS	1DH	DOWN (Edit)

14	SO	0EH	F5	30	RS	1EH	LEFT (Edit)

15	SI	0FH	F6	31	US	1FH	RIGHT (Edit)

To emulate the keyboard function key input for user definable parameters, user must configure actual content using the Reserved ASCII 0 – 31 characters, and also Enable the “Function Key Emulation”. Otherwise, the Ctrl output will be done by the scanner. Please refer to the above Keyboard Function Code Table which is for IBM PC/XT/AT, PS/2, PS/VP, COMPAQ PC, HP Vectra PC, Notebook PC, APPLE and PowerMac, and WYSE PC Enhanced or fully compatible machines.

70

Contents

International Edition, Rev. B5 Description 1 – Add “Indications” Serial Response Time-out Remove ”Scan Voting” and add “Scan Rate Control ” Quantity Output Format Rev. A7 Nov 10 Baud Rate – Cancel Baud Rate 300/600 BPS Rev. No Warranty Regulatory LED Eye Safety Laser Eye Safety Getting Started Configure Your FuzzyScan Appendix F700BT Series Scanner HB2110 Smart Cradle (Base) F600BT Series Scanner HB2100 Charging Cradle (Base) Install the Battery Charging the Battery PAIR Mode PICO Mode HID Mode SPP Master/Slave Mode Preparations before Using Turn on the power of your host device alternating red and green blinks 1 blue blink per 2.5 seconds alternative red and green blinks over steady green Clone Function Page Establish SPP Master Connection Establish SPP Slave Connection no longer How to Transmit Stored Data Using Quantity Feature System Command Family Code Option Code Programming Procedures Conventions of Programming Menu Program & End System List, Group & Master Default System List, Gro Single scan selection Multiple scans selection Cycling scan selection Dual level selection Reference Manual ♦ User Defined Symbol ID ♦ ♦ Symbology ID Transmission ♦ Family Code Selection P.C Option Code ♦ Readable Bar Code Setting ♦ ♦ Code 39/Code 32 Setting ♦ Disable Code Enable Code 39 Select Standard Code 39 as primary format Select Full ASCII Code 39 as primary format ♦ Code 39 Setting ♦ Level Level 2 Code 39 Security Level The scanner offers four levels of decode security for Code39 bar codes: ♦ Codabar/NW-7Setting ♦ Codabar Setting Disable Codabar Enable Codabar Select Codabar standard format Page ♦ UPC-A& UPC-ESetting ♦ UPC Family Setting Disable UPC-A Enable UPC-A Disable UPC-E Page ♦ EAN Setting ♦ UPC/EAN Security Level ♦ UCC Coupon Extended Code Setting ♦ P.CParameter Selection ♦ IATA & Interleaved 2 of 5 Setting ♦ ♦ Code 25 Family Setting ♦ Disable Standard/Industrial 2 of 5 Enable Standard/Industrial 2 of Disable Matrix 2 of 5 Enable Matrix 2 of ♦ Code 11 & Code 93 Setting ♦ Disable Code 11 Enable Code Select 1-checkdigit verification Select 2-checkdigit verification ♦ MSI/Plessey Setting ♦ Disable MSI/Plessy Enable MSI/Plessy Select MOD 10 check digit Select MOD 10-10check digit ♦ Code 128 & UCC/EAN 128 Setting ♦ Disable Code 128 and GS1-128 Enable Code 128 and GS1-128 Disable function code conversion Enable function code conversion ♦ UK/Plessey Setting ♦ Disable UK/Plessey Enable UK/Plessey Select UK/Plessey Standard Format Select UK/Plessey CLSI Format ♦ Telepen Setting ♦ Disable Telepen Enable Telepen Select Telepen Numeric mode Select Telepen Full ASCII mode ♦ GS1 DataBar Setting ♦ Disable GS1 DataBar (RSS-14) Enable GS1 DataBar (RSS-14) Disable GS1 DataBar Limited Enable GS1 DataBar Limited ♦ Linear-stacked& Korea Post Code Setting ♦ ♦ Keyboard Layout (Language) Setting ♦ USA (QWERTY) France (AZERTY) Germany (QWERTZ) United Kingdom - UK (QWERTY) ♦ Record Suffix, Preamble, Postamble & Caps Lock ♦ Caps Lock Control ♦ Delay Setting ♦ 1-99(x10) msec 1-99(x5) msec ♦ Emulation Setting & Upper/Lower Case Setting ♦ ♦ Record Suffix, Preamble ,Postamble Setting ♦ STX/ETX Control Disable STX/ETX transmission Enable STX/ETX transmission data frame transmitted via serial interface Page ♦ Protocol, ACK/NAK Setting ♦ None (free running mode) RTS/CTS (hardware handshaking) ACK/NAK (software handshaking) Xon/Xoff (software handshaking) Page ♦Time Out Setting, Baud Rate, Data Frame ♦ F_DEFAULT 3 seconds 200 mseconds 4 seconds ♦ Code 39/Code 128 Emulation ♦ High level (5Vdc) on Bar (low level on Space) Low level (0Vdc) on Bar (high level on Space) Determine the output voltage level for both bar and space Initial Signal State Reference Manual ♦ Buzzer, Indicator, Vibrator, Inverse Reading ♦ Buzzer Tone Adjust Good Read Indicator ♦ Dollar Sign Control, Redundancy, Scan Rate Control ♦ Dollar Sign Control Dollar sign output as “ $ “ Dollar sign output as “ “ Dollar sign output as “ € “ Page ♦ Time-outSetting, Good Read Duration ♦ ♦ Presentation Scanning Setting, Laser Aiming Control ♦ 3 mins 5 mins 10 mins Only available for FuuzzyScan Laser model ♦1D Barcode Direction Indication Transmission, etc. ♦ 1D Barcode Direction ♦ Out-of-rangeScanning, Sleep Time-outControl ♦ Out-of-rangeScanning Link Supervision Time-out 3 secs Only available in PAIR & PICO modes ♦ Batch Scanning Setting ♦ Batch Scanning Link Control Radio disable Radio enable All ♦ Batch Scanning Data Transmission Setting ♦ User define As many times as the quantity indicates <Quantity><Field Delimiter><Scanned Data <Scanned Data><Field Delimiter><Quantity ♦ Bluetooth Device Name & Security Setting♦ Default device name User define, 1-16characters Default Bluetooth PIN Code User define, 1-8numbers ♦ Bluetooth Other Settings ♦ ♦ Preamble, Postamble, Data Length & Symbol ID Trans. ♦ Enable 2 digits data length transmission If data length exceeds 99, 3-digitdata length will be transmitted Enable prefix symbology ID transmission Enable suffix symbology ID transmission ♦ Data Formatter Setting ♦ Formatter Control Select one bar code symbology Select all bar code symbologies 1st Insertion ♦ Data Verifier Setting ♦ 2nd Option Code Verifier Control Identified Data Length Determine the identified data length for verification ♦ Data Replacer Setting ♦ Replacer Control 2-digitsidentified position; 1 replacement character ♦ Data Organizer Setting ♦ Organizer Control 1st Organization 0 (Forward) 2-digitsidentified position; Select a Bar Code Symbology Position Calculation Application Example Programming Procedure Appendix Each AIM Code Identifier contains the three-characterstring ]cm where: ]cm ]= Flag Character c = Code Character m = Modifier Character Reserved ASCII 0 – Enable HEX HEX/ASCII Table Example: PREAMBLE Hex/ASCII Table Reference Manual Page (Work with Smart Cradle only) FIN (Finish) END (Exit) Page PROGRAM Save Configuration (Enter Programming Mode) Clone END Descriptions Link Indicator Beeper Status Indicator HB2100 Charging Cradle Indication HB2110 Smart Cradle Indications CINO GROUP