Manuals / Cisco Systems / Computer Equipment / Network Router

Cisco Systems AIRCAP3602ITK9, AIRCAP3602IAK9RF Installing Modules, Installing a Module

Models: AIRCAP3602ISK9 AIRCAP3602EAK9 AIRCAP3602IAK9RF AIRCAP3602ITK9

1 40

Download 40 pages 31.6 Kb

Page 16

10Installing Modules

10Installing Modules

Modules are devices that are purchased as seperate items. When they are installed in the Cisco Aironet 3600 series access point, they give the access point additional capabilities.

Modules connect to the access point’s module port. No special tools are required to install a module.

Installing a Module

Follow these steps to install a module:

Step 1 Remove the module from the packaging.

Step 2 Power down the access point.

Step 3 Peel off the label from the back of the 3600 series access point to reveal the module port connector.

1

2

1

1

		345379
Openings for module’s antennas.	2	Label covering port connector.

16

Image 16

Cisco Systems AIRCAP3602ITK9, AIRCAP3602IAK9RF, AIRCAP3602EAK9, AIRCAP3602ISK9 Installing Modules, Installing a Module

Contents

Cisco Aironet 3600 Series Lightweight Access Points GETTING STARTED GUIDE2 Introduction to the Access Point 1 About this Guide3 Safety Instructions IMPORTANT SAFETY INSTRUCTIONStranslated safety warnings that accompanied this device. Statement SAVE THESE INSTRUCTIONS20A. Statement 4 Unpacking 5 ConfigurationsExternal Antennas Regulatory Domains Internal AntennasCountries Supported 6 Access Point Ports and Connectors Figure 2 Access Point LED Indicator top-3602I Model LED indicator272377 7 Configuring the Access Point The Controller Discovery ProcessPreparing the Access Point Installation Summary Performing a Pre-Installation ConfigurationPre-Installation Configuration Setup Controller Layer 3 devices Cisco Aironet access pointsStep 2 Apply power to the access point 2106 controller WS-C3550, WS-C3560, and WS-C3750 switchesC1880 switch 2600, 2610, 2611, 2621, 2650, and 2651 multiservice platformsc. If the access point shuts down, check the power source 8 Mounting the Access Point 9 Deploying the Access Point on the Wireless Network10 Installing Modules Installing a ModuleStep 5 Screw down the thumb screws on the module 11 Troubleshooting Guidelines for Using Cisco Aironet Lightweight Access PointsUsing DHCP Option Checking the Access Point LEDStatus LED Message StatusMessage TypeTroubleshooting the Access Point Join Process 12 Declarations of Conformity and Regulatory Information Tested To Comply With FCC Standards FOR HOME OR OFFICE USEAccess Point Models Module ModelsVCCI Statement for Japan Guidelines for Operating Cisco Aironet Access Points in Japan Japanese TranslationEnglish Translation 03-6434-6500Statement 371-Power Cable and AC Adapter Industry CanadaCanadian Compliance Statement English TranslationEuropean Community, Switzerland, Norway, Iceland, and Liechtenstein Access Point ModelsModule Models Page Health & Safety-EN60950-1 2005 EN 50385 The following standards were appliedEMC-EN 301.489-1 v1.8.1 EN 301.489-17 Radio-EN 300 328 v 1.7.1 EN 301.893 vDeclaration of Conformity for RF Exposure Generic Discussion on RF ExposureThis Device Meets FCC Guidelines for Exposure to Radio Waves Additional Information on RF Exposure Administrative Rules for Cisco Aironet Access Points in Taiwan Chinese TranslationEnglish Translation Administrative Rules for Low-power Radio-Frequency Devices ArticleChinese Translation Operation of Cisco Aironet Access Points in Brazil Regulatory InformationAccess Point Models English TranslationDeclaration of Conformity Statements Portuguese TranslationEnglish Translation Module ModelsCisco AP c3600-ServiceProvider 13 Configuring DHCP Option 43 and DHCP OptionCisco AP c3600 14 Access Point Specifications Type + Length + ValueSpecification Categoryrefer to Channels and Maximum Power Settings for Cisco Aironet Access Point Specifications continued15 Obtaining Documentation and Submitting a Service Request