Manuals / Brands / Household Appliance / Water System / Cisco Systems / Household Appliance / Water System

Cisco Systems BC-23 Monitoring and Maintaining the PA-12E/2FE Port Adapter

1 62

Download 62 pages, 661.74 Kb

Configuring Transparent Bridging

Transparent and SRT Bridging Configuration Task List

BC-57

Cisco IOS Bridging and IBM Networking Configuration Guide

To enable integrated routing and bridging on the bridge groups, perform the following tasks beginning

in global configuration mode:

Monitoring and Maintaining the PA-12E/2FE Port Adapter

After configuring the new interface, you can display its status and verify other information. To display

information about the PA-12E/2FE port adapter, perform the following tasks in EXEC mode:

Step8 Repeat Step 1 through Step 7 for each interface.

Step9 copy running-config startup-config Saves the new configuration to memory.

Command Purpose

Command Purpose

Step1 bridge irb Enables integrated routing and bridging.

Step2 interface bvi bridge-group Enables a virtual interface on a bridge group.

Step3 ip address address mask Assigns an IP address and subnet mask to the bridge group virtual

interface.

Step4 no shutdown Changes the shutdown state to up.

Step5 exit Returns to configuration mode.

Step6 Repeat Step 1 through Step 5 for each interface.

Step7 bridge bridge-group route protocol Specifies the protocol for each bridge group.

Step8 exit Exits configuration mode.

Step9 copy running-config startup-config Saves the new configuration to memory.

Command Purpose

show version Displays the configuration of the system hardware, the software version, the

names and sources of configuration files, and the boot image.

show controllers Displays all current port adapters and their interfaces.

show interface fastethernet slot/port

(for ports 0 and 1)

show interface ethernet slot/port

(for ports 2 through 13)

Verifies the interfaces have the correct slot number and that the interface and

line protocol are in the correct state.

show bridge group Verifies all bridge groups and their interfaces.

show interface ethernet slot/port irb

(ports 2 through 13)

show interface fastethernet slot/port

irb

(ports 0 and 1)

Verifies the correct routed protocol is configured for each interface.

show protocols Displays the protocols configured for the entire system and specific

interfaces.

show pas eswitch addresses fastethernet

slot/port

(ports 0 and 1)

show pas eswitch addresses ethernet

slot/port

(ports 2 through 13)

Displays the Layer 2 learned addresses for each interface.

Contents

Main Configuring Transparent Bridging Technology Overview Transparent and SRT Bridging Transparent Bridging Features Integrated Routing and Bridging Bridge-Group Virtual Interface Page Other Considerations SRT Bridging Features Transparent and SRT Bridging Configuration Task List Configuring Transparent Bridging and SRT Bridging Assigning a Bridge Group Number and Defining the Spanning-Tree Protocol Assigning Each Network Interface to a Bridge Group Choosing the OUI for Ethernet Type II Frames Transparently Bridged VLANs for ISL Page Routing between ISL VLANs Page Configuring a Subscriber Bridge Group Configuring Transparent Bridging over WANs Configuring Fast-Switched Transparent Bridging over ATM Configuring Transparent Bridging over DDR Configuring Transparent Bridging over Frame Relay Configuring Transparent Bridging over Multiprotocol LAPB Configuring Transparent Bridging over SMDS Configuring Transparent Bridging over X.25 Configuring Concurrent Routing and Bridging Configuring Integrated Routing and Bridging Assigning a Bridge Group Number and Defining the Spanning-Tree Protocol Configuring Interfaces Enabling Integrated Routing and Bridging Configuring the Bridge-Group Virtual Interface Configuring Protocols for Routing or Bridging Configuring Transparent Bridging Options Disabling IP Routing Enabling Autonomous Bridging Configuring LAT Compression Establishing Multiple Spanning-Tree Domains Preventing the Forwarding of Dynamically Determined Stations Forwarding Multicast Addresses Configuring Bridge Table Aging Time Filtering Transparently Bridged Packets Setting Filters at the MAC Layer Filtering by Specific MAC Address Page Page Page Filtering LAT Service Announcements Specifying Deny or Permit Conditions for LAT Group Codes on Output Adjusting Spanning-Tree Parameters Setting the Bridge Priority Setting an Interface Priority Assigning Path Costs Adjusting BPDU Intervals Disabling the Spanning Tree on an Interface Configuring Transparent and IRB Bridging on a PA-12E/2FE Ethernet Switch Configuring the PA-12E/2FE Port Adapter Monitoring and Maintaining the PA-12E/2FE Port Adapter Configuring Bridge Groups Using the 12E/2FE VLAN Configuration WebTool Page Tuning the Transparently Bridged Network Configuring Circuit Groups Configuring Constrained Multicast Flooding Monitoring and Maintaining the Transparent Bridge Network Transparent and SRT Bridging Configuration Examples Basic Bridging Example BC-64 The configuration file for the router in Figure 12 is as follows: Concurrent Routing and Bridging Example BC-65 Basic Integrated Routing and Bridging Example Figure 13 Basic IP Routing using Integrated Routing and Bridging The following example shows the relevant portions of the configuration for the router in Figure 13: BC-66 Complex Integrated Routing and Bridging Example Figure 14 Complex Integrated Routing and Bridging Example The following example shows the relevant portions of the configuration for the router: BC-67 Integrated Routing and Bridging with Multiple Bridge Groups Example Figure 15 Integrated Routing and Bridging with Multiple Bridge Groups The following example shows the relevant portions of the configuration for the router in Figure 15: Transparently Bridged VLANs Configuration Example BC-68 Router One Router Two BC-69 Router Three BC-70 Routing between VLANs Configuration Example Ethernet-to-FDDI Transparent Bridging Example Ethernet Bridging Example SRT Bridging Example BC-73 Configuration for the New York City Router Configuration for the Thule, Greenland Router Multicast or Broadcast Packets Bridging Example Figure 18 Network Demonstrating Output Address List Filtering BC-74 The correct access list would be as follows: X.25 Transparent Bridging Example Figure 19 X.25 Bridging Examples Following are the configuration commands for each of the bridges depicted in Figure19: X.25 Bridge 2 Bridge 1 Bridge 3 BC-75 Frame Relay Transparent Bridging Examples Figure 20 illustrates three bridges connected to each other through a Frame Relay network. Figure 20 Frame Relay Bridging Example Bridging in a Frame Relay Network with No Multicasts Bridge 2 Bridge 1 Bridge 3 Transparent Bridging over Multiprotocol LAPB Example BC-77 Fast-Switched Transparent Bridging over ATM Example (Cisco 7000) The following configuration example enables fast-switched transparent bridging over ATM: Transparent Bridging over DDR Examples Fast-Switched Transparent Bridging over SMDS Example Complex Transparent Bridging Network Topology Example Page Page Page BC-82 Fast Ethernet Subscriber Port, Frame Relay Trunk Example ATM Subscriber Ports, ATM Trunk Example The following example uses ATM subinterfaces as the subscriber ports and the ATM as the trunk: BC-83 Configuration of Transparent Bridging for PA-12E/2FE Port Adapter Example BC-84 Configuration of IRB for PA-12E/2FE Port Adapter Example