Chapter 3 Technical and Environmental Specifications
Equipment Rack Specifications
Table
|
|
|
| Load (weight) rating | The rack must support the following weights and specifications: | ||
|
|
|
|
| • 650 lb (294.8 kg) single chassis with full cosmetics | ||
|
|
|
|
| • 1300 lb (589.7 kg) two chassis, each with full cosmetics | ||
|
|
|
|
| • 95 lb (43.0 kg) or more for each chassis for cabling | ||
|
|
|
|
| • Additional weight of other components in rack | ||
|
|
|
|
| Note ANSI specification T1.336 (2003), which defines static load | ||
|
|
|
|
|
| and safety margins, recommends that racks be designed to | |
|
|
|
|
|
| support at least two times the anticipated load. | |
|
|
|
|
| Note See ANSI specification T1.329 (2002) for dynamic load | ||
|
|
|
|
|
| requirements and earthquake resistance specifications. | |
|
|
|
|
|
| ||
|
|
|
| Chassis and rack footprint | 5.9 sq. ft (0.55 sq. m), 23.6 in. rack width by 36 in. chassis length | ||
|
|
|
| (floor contact area) |
|
|
|
|
|
|
| Maximum floor loading | 600 lb/4.5 sq. ft = 133 lb/sq. ft (without cosmetics or doors) | ||
|
|
|
|
| 272.2 kg/4134.2 sq. cm = .07 kg/sq. cm | ||
|
|
|
|
| 650 lb/4.9 sq. ft = 132.7 lb/sq. ft (with cosmetics and doors) | ||
|
|
|
|
| 294.8 kg/4580.1 sq. cm = .06 kg/sq. cm | ||
|
|
|
|
| Note Be sure to include the weight of the rack when you consider | ||
|
|
|
|
|
| floor loading requirements. The above numbers do not | |
|
|
|
|
|
| include rack weight. | |
|
|
|
|
|
|
|
|
|
|
|
| Rack Anchoring |
|
|
|
|
|
|
| General considerations | • The rack must be bolted to the floor. For more information, see | ||
|
|
|
|
|
| the Cisco | |
|
|
|
|
|
| Unpacking, Moving, and Securing Guide. | |
|
|
|
|
| • Consider floor and overhead anchoring requirements for the site, | ||
|
|
|
|
|
| and size and load capacity of anchors and floor structure. | |
|
|
|
|
| • Make sure that floor mounting bolts are accessible, especially if | ||
|
|
|
|
|
| annual retorquing of bolts is required. | |
|
|
|
| Floor mounting holes | • | Outrigger | |
|
|
|
|
|
| ||
|
|
|
|
| • | Internal frame holes: | |
|
|
|
|
|
| ||
|
|
|
|
| • For all other racks, check with rack manufacturer. | ||
|
|
|
|
|
|
|
|
|
|
|
| Chassis Clearances |
|
|
|
|
|
|
| Two chassis in a single rack | |||
|
|
|
| Front and rear of chassis | |||
|
|
|
|
| |||
|
|
|
| Inlet and exhaust openings on | |||
|
|
|
| chassis and power modules |
|
|
|
|
|
|
| Top of chassis | No overhead clearance for a single chassis. Two chassis in a rack | ||
|
|
|
|
| requires | ||
|
|
|
|
|
| ||
|
|
| Cisco | ||||
|
|
| |||||
|
|
|
|
|
| ||
|
|
|
|
|
|