Installation Requirements

Electrical Equipment Guidelines

Follow these basic guidelines when working with any electrical equipment:

•Before beginning any procedures requiring access to the router interior, locate the emergency power-off switch for the room in which you are working.

•Disconnect all power and external cables before moving a router.

•Do not work alone when potentially hazardous conditions exist.

•Never assume that power has been disconnected from a circuit; always check.

•Do not perform any action that creates a potential hazard or makes the equipment unsafe.

•Carefully examine your work area for possible hazards such as moist floors, ungrounded power extension cables, and missing safety grounds.

Preventing Electrostatic Discharge Damage

Electrostatic discharge (ESD) damage, which can occur when electronic cards or components are improperly handled, results in complete or intermittent failures.

Use the following guidelines for preventing ESD damage:

•Always use an ESD wrist or ankle strap and ensure that it makes good skin contact.

•Connect the equipment end of the strap to an unfinished chassis surface.

•When installing a component, use any available ejector levers or captive installation screws to properly seat the bus connectors in the backplane.

•When removing a component, use any available ejector levers or captive installation screws to release the bus connectors from the backplane or midplane.

•Handle carriers by available handles or edges only; avoid touching the printed circuit boards or connectors.

•Place a removed board component-side-up on an antistatic surface or in a static shielding container; otherwise, immediately place it in a static shielding container.

•Avoid contact between the printed circuit boards and clothing. The wrist strap only protects components from ESD voltages on the body; ESD voltages on clothing can still cause damage.

•Never attempt to remove the printed circuit board from the metal carrier.

Caution For safety, periodically check the resistance value of the antistatic strap. The measurement should be between 1 and 10 megohms (Mohm).

RSP4+ Bootflash Memory Upgrade to 16MB Installation and Configuration Guide

 

78-12288-02

7

 

 

 

Page 6 Page 8
Page 7
Image 7
Cisco Systems MEM-16F-RSP4+= manual Electrical Equipment Guidelines, Preventing Electrostatic Discharge Damage
Page 6 Page 8

MEM-16F-RSP4+= specifications

Cisco Systems has designed the MEM-16F-RSP4+ specifically to enhance the memory capabilities of its high-performance routers, such as the Cisco 7600 series. This memory module is integral to the efficient functioning of the Route Processor 4 (RSP4) by providing an additional 16 GB of DRAM. This increase in memory is critical for network operators who require enhanced performance, scalability, and faster data processing capabilities in their networks.

One of the standout features of the MEM-16F-RSP4+ is its robust support for a wide range of services and applications. With the additional memory, users can support more concurrent sessions, higher traffic loads, and more complex routing policies without compromising on performance. This capability is particularly important for service providers and enterprises that rely on advanced services such as Voice over IP (VoIP), video streaming, and large-scale data storage.

The MEM-16F-RSP4+ also plays a vital role in improving the overall reliability and stability of the system. With increased memory, the router can perform more functions simultaneously, effectively handling larger tables and allowing for efficient processing of routing protocols. This not only enhances the router’s performance under heavy loads but also minimizes the risk of bottlenecks in data traffic, leading to smoother network experiences.

In terms of technologies, the MEM-16F-RSP4+ is designed to integrate seamlessly with Cisco's IOS software, ensuring compatibility with existing configurations and applications. This integration allows for quicker deployment and minimal disruption during upgrades. Additionally, the memory module is hot-swappable; network operators can replace or upgrade hardware without interrupting ongoing network operations, thus enhancing overall uptime.

The MEM-16F-RSP4+ is characterized by its reliability, which is crucial for mission-critical applications. Cisco rigorously tests its memory modules to meet specific performance metrics, ensuring that they can withstand the demanding environments typical of enterprise and service provider networks. With this high standard of testing and quality assurance, the MEM-16F-RSP4+ stands out as a preferred option for organizations aiming to future-proof their networking infrastructure.

Overall, the Cisco MEM-16F-RSP4+ memory module is an essential component for anyone utilizing the Cisco RSP4 router. Its features and capabilities contribute significantly to improved network performance and reliability, enabling organizations to meet the ever-growing demands of modern data communications and services.
Top Page Image Contents