Cisco Systems XR 12000 Series Installing a Line Card

13

CiscoXR 12000 Series Router Ethernet Line Card Installation

OL-7861-01

Removing and Installing a Line Card

Caution Be careful not to damage or disturb the EMI spring fingers located on the front edge of the card face

plate.

Note Always insert a dust plug in an optical port opening for each port that is not in use.

For information on disconnecting interface cables, see the “Removing and Installing Fiber-Optic

Interface Cables” section on page52.

For information on removing the cable-management bracket, see the “Removing a Line Card

Cable-Management Bracket” section on page 39.

Installing a Line Card

A line card slides into almost any available line card slot and connects directly to the backplane. If you

install a new line card, you must first remove the line card blank from the available slot.

Note Refer to the installation and configuration guide for your router for information on line card slot types,

slot width, and slot location.

Caution The router may indicate a hardware failure if you do not follow proper procedures. Remove or insert only

one line card at a time. Allow at least 15seconds for the router to complete the preceding tasks before

removing or inserting another line card.

To install a line card, follow these steps:

Step1 Attach an ESD-preventive wrist or ankle strap and follow its instructions for use.

Step2 Choose an available line card slot for the line card, and verify that the line card interface cable is long

enough for you to connect the line card with any external equipment.

Caution To prevent ESD damage, handle line cards by the captive installation screws, the provided handle, ejector

levers, or the card carrier edges only. Do not touch any of the electrical components or circuitry.

Step3 Grasp the faceplate (or handle) of the line card with one hand and place your other hand under the card

carrier to support the weight of the card; position the card for insertion into the card cage slot. Avoid

touching the line card printed circuit board, components, or any connector pins.

Step4 Carefully slide the line card into the slot until the ejector levers make contact with the edges of the card

cage, then stop when the ejector lever hooks catch the lip of the card cage. If they do not catch, try

reinserting the line card until the ejector lever hooks are fully latched. (See Figure5.)

Contents

Main Cisco XR 12000 Series Router Ethernet Line Card Installation Contents Important Information Ethernet Line Card Product Numbers Router Hardware Installation Supported Platforms Cisco IOS Software Release and Hardware Revision Requirements Memory Options Related Documentation Product Overviews Ethernet Line Card Comparison 4-Port Gigabit Ethernet ISE Line Card 10-Port 1-Gigabit Ethernet Line Card Page 1-Port 10-Gigabit Ethernet Line Card 51 2 34 Preparing for Installation Safety Guidelines Preventing Electrostatic Discharge Required Tools and Equipment Removing and Installing a Line Card Guidelines for Line Card Removal and Installation Removing a Line Card CiscoXR 12000 Series Router Ethernet Line Card Installation Removing and Installing a Line Card b the ports on the line card. c Line card connector. (See Figure4b.) to return it to the factory. Installing a Line Card Page Removing and Installing EPAs Removing an EPA from the Modular Gigabit Ethernet Line Card Page Inserting an EPA into a Modular Gigabit Ethernet Line Card A B C ATTENTION: Page CiscoXR 12000 Series Router Ethernet Line Card Installation Removing and Installing EPAs Figure10 Side Views - Mating the Connector of the EPA to the Line Card Figure11 Press on the Rear Outer Corners of the EPA with your thumbs to the two rear outer corners of the EPA, as shown in Figure11 and Figure 12. 20 Max 4 Max PUSH Figure12 Rear Outer Corners of the EPA (Close-up) Figure13 Press on the White Labels on the EPA PUSH Page Removing and Installing GBICs General GBIC Handling and Maintenance Guidelines Removing the GBIC from an Ethernet Line Card Inserting a GBIC into the Gigabit Ethernet Interface Removing and Installing SFP Modules Bale Clasp SFP Module Removing a Bale Clasp SFP Module Removing and Installing SFP Modules you plan to return it to the factory. Figure18 Removing a Bale Clasp SFP Module Installing a Bale Clasp SFP Module Mylar Tab SFP Module Removing a Mylar Tab SFP Module Installing a Mylar Tab SFP Module Actuator Button SFP Module Removing an Actuator Button SFP Module Removing and Installing SFP Modules Figure24 Removing an Actuator Button SFP Module from a Port the port. you plan to return it to the factory. Installing an Actuator Button SFP Module Slide Tab SFP Module Removing a Slide Tab SFP Module Installing a Slide Tab SFP Module Line Card Cable-Management Bracket Page Removing a Line Card Cable-Management Bracket 1Chassis cable-management tray 3Line card cable-management bracket 2Velc ro str ap s 4Fiber cable ab Installing a Line Card Cable-Management Bracket Cabling and Specifications Fast Ethernet Interface Page Gigabit Ethernet Interface GBIC Laser Optical Transceiver Modules GBIC Modules Page Using CWDM GBICs with the 3-Port Gigabit Ethernet Line Card General CWDM GBIC Installation and Usage Guidelines Related CWDM Documentation General Connection Rules for CWDM GBICs Gigabit Ethernet SFP Modules Page 10-Gigabit Ethernet Fiber-Optic Interface Cables 1 2 Removing and Installing Fiber-Optic Interface Cables Removing Fiber-Optic Interface Cables Cabling and Specifications Figure40 Disconnecting Line Card Interface Cables Installing Fiber-Optic Interface Cables 1Fiber cable 3Cable-management bracket 5SFP module 2Velc ro str ap 4Dust plug ACTIVE CARRIER RX PACKET ab 1 Cleaning Fiber-Optic Connectors Type RJ-45 100BASE-T Copper Cables Removing and Installing RJ-45 100BASE-T Copper Cable Removing RJ-45 Cables Installing RJ-45 Cables Verifying and Troubleshooting the Installation Initial Boot Process Status LEDs Gigabit Ethernet Status LEDs Alphanumeric LEDs Table 1 8 and Tabl e 19 may not appear on your line card. LED Color/Activity Description Page Page Page Troubleshooting the Installation Line Card Memory Line Card Memory Locations Engine 2 Line Card Memory Locations ISE Line Card Memory Locations Line Card Memory Figure46 ISE Line Card Memory Locations 4OC12X/SRP-IR-LC A B A Engine 4 Line Card Memory Locations Ethernet Line Card Route Memory Options Ethernet Line Card Packet Memory Options Removing and Installing Line Card Memory Removing a DIMM Installing a DIMM Removing a SODIMM Page Installing a SODIMM Page ab Page Checking the Installation of Line Card Memory Regulatory, Compliance, and Safety Information Translated Safety Warnings and Agency Approvals Electromagnetic Compatibility Regulatory Statements FCC Class A Compliance CISPR 22 Canada English Statement of Compliance French Statement of Compliance Europe (EU) Class A Notice for Hungary Class A Notice for Taiwan and Other Traditional Chinese Markets VCCI Class A Notice for Japan Class A Notice for Korea Laser Safety Class 1 Laser Product Warning (Single-mode) Class 1 LED Product Warning (Multimode) General Laser Warning Obtaining Documentation and Submitting a Service Request