Manuals / ClearOne comm / Communications / Conference Phone

ClearOne comm XAP 800 operation manual Type, Inputs 1-8 Filters window

Models: XAP 800

1 151

Download 151 pages 52.56 Kb

Page 43

36	System Configuration ~ Inputs and Outputs

Figure 3.32. Inputs 1–8 Filters window

Type

Use the Type list to select from the following input filters: All Pass, High Pass, Low Pass, Notch, and PEQ. G-Ware features other filters which are configured in the Processing section of the software (see page 49).

•All Pass. Frequency range is 20Hz to 20kHz with resolution to 1Hz or four places (whichever is larger).

•High Pass. Selectable frequency cutoff is 20Hz to 20kHz, in 1Hz increments. Rolloff is 12dB/octave. Level is fixed at 0dB.

•Low Pass. Selectable frequency cutoff is 20Hz to 20kHz in 1Hz increments. Rolloff is 12dB/octave. Level is fixed at 0dB.

•Notch. Center frequency range is 20Hz to 20kHz with resolution to 1Hz or four places (whichever is larger). Bandwidth is from .05 to 5 octaves in .01 octave increments. Level is fixed at -80dB.

•PEQ (parametric equalizer). Center frequency range is 20Hz to 20kHz with resolution to 1Hz or 4 places (whichever is larger). Bandwidth is .05 to 5 octaves in .01 octave increments. Level range is -15 to +15dB in 0.5dB increments.

Frequency. Use Frequency to select the center frequency (in Hertz) for the filter you are configuring. Range is from 20Hz to 20kHz. Default is 1kHz.

Gain. Gain adjusts the gain value from -18 to 18dB, in .5dB steps. Default is 0dB.

Q, or Quality factor. Q, or Quality factor, selects the ratio of the center frequency divided by the bandwidth. Q reflects an inverse relationship to the bandwidth, and adjusts from .02:1 to 40:1 on the XAP 800.

Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760

Image 43

ClearOne comm XAP 800 operation manual Type, Inputs 1-8 Filters window

Contents

Audio Products XAP 800 Audio Conferencing System XAP 800 Audio Conferencing System XAP 800 Installation ClearOne Part No July 2002 Rev Iii Table of ContentsSystem Configuration Advanced ConfigurationControl OperationAppendices Technical Services Group ~ 1-800-283-5936 USA ~ Product overview IntroductionIntroduction ~ New Features New FeaturesClearOne Communications EuMEA GmbH Professional Services GroupSales and Customer Service Technical SupportSecurity page 26 for more details UnpackingControls and Connections Front panelIntroduction ~ Controls and Connections Rear panelIntroduction ~ Controls and Connections Expansion bus NetworkingEnvironmental PowerEquipment placement Operational RequirementsHardware Setup InstallationTo connect the unit Installation ~ Hardware SetupTo create an expansion bus network Installation ~ Networking UnitsNetworking Units Expansion bus connectionsTo assign device IDs Mixer modeTo select a mixer mode Device IDsPressing Esc at the top of the tree does nothing Installation ~ LCD ProgrammingLCD Programming LCD menu treeRun Macro To adjust a parameterSelect Preset System menuRS-232 menu Flow Control hardware Enable ModemClear Password Meter menuProcessing Default MeterInputs menu OutputsGain Outputs menuMeter Reference Point diagram Technical Services Group ~ 1-800-283-5936 USA ~ Ware Requirements System ConfigurationTo install G-Ware Installing G-WareCreating Floppy Disk Copies To create a new site Site SetupControl using Creating a new siteSelect the XAP 800 icon and click Add Adding a XAPTo auto-detect units To manually add unitsTo configure Unit Properties Configuring Unit Properties14. Unit Properties Security tab Flow Screen Ware ScreensSafety Mute Copying and pasting settingsStatus bar Matrix Screen System Configuration ~ G-Ware ScreensCross point attenuation Audio RoutingExpansion bus O-Z routing Process A-H routingMatrix report System Configuration ~ Audio RoutingInputs Inputs and OutputsPA Adapt and AEC Reference Pwr Phantom PowerTarget ThresholdClick Close to exit the window To create a virtual referenceActive Filter FiltersNon-linear Processing NLP Meters32. Inputs 1-8 Filters window TypeTable View To configure filtersChairman Override PA Adaptive ModeGate ActivationAmbient Level Gate RatioHold Time Off Attenuation38. Virtual Reference window Gating Group Select To configure gating group settingsTo assign a gating group Min/Max limits Click the Gating Group label to change the group namesMeters AGC 47. Gain meters NOM OutputsOptimizing output gain structure From Expansion Bus O-Z Expansion BusesTo Expansion Bus O-Z Processing A-H ProcessingGroup Cmprs compressor54. Processing Filters window Remove Filter PhaseBypass Add FilterChanges you make in the distance and temperature fields DelayOptimizing process gain structure 57. Process Gain adjust and meterCreating Presets PresetsOverview Affected when the preset is run Preset Configuration panePreset password is set in the Unit Properties window see Advanced Configuration ~ Presets Assigning virtual references to the preset To enable Acoustic EchoStorage space To create a presetTo run a preset using front panel control Running presetsRunning multiple presets simultaneously To run a preset using G-WareRoom combining example All presets are ready to run againFour macros one for each configuration are set up as follows Macros To create a macro using Macro RecorderCreating macros 16 Macro Name window To create a macro using Macro EditorTo delete a macro To add or insert a command lineEditing macros To edit a macroRunning macros To run a macro using front panel controlTo run a macro using the Select panel or Gpio Use the macro command. See Control for more detailsSelect the XAP 800 Unit and Input Channel you want to use Signal GeneratorUtilities To use pink or white noiseTo use tone Document Compare UtilityTo compare site files Open window Operation ~ UtilitiesPrint Preview window Copying settingsPrint Reports window Print ReportsGFirm Firmware Utility To upgrade firmwareToolbar Button 13. Selecting baud rate Copy and paste settings Ware SwitcherTo use G-Ware Switcher Operation ~ Monitoring Views Message LogMonitoring Views Gate ViewMeter Views To configure Meter ViewsGpio Builder To program control/status pinsControl/Status a XAP IR Remote Remote BuilderClearOne Control Panels Select IR Remote default from the Select Remote Type listControl ~ Remote Builder To program the XAP IR Remote One IR remote can be To program the Volume panelTo program the Select panel Control ~ Remote BuilderSerial commands Remote Modem AccessRS-232 Port Control ~ RS-232 Port Command stringsTo create a command string To run a command stringTechnical Services Group ~ 1-800-283-5936 USA ~ Appendix a Specifications Ambient Level Filters Maximum # of Mics Mode Noise Cancellation on/offPin Number Control Appendix B PinoutsRS-232 COM DCE port pinout female Appendices ~ Appendix B PinoutsControl/Status a Port Pinout female Control/Status connectorsFirst 16 pins on Pin Definable Type Default DescriptionPreset select status for Pin Preset select bitControl/Status B port pinout Pin Description RS-485 Remote Panel a and B connectorsSet connector pinout Line connector pinoutAppendix C Control Panel Connecting the Control PanelAppendices ~ Appendix C Control Panel Appendices ~ Appendix C Control Panel AssemblyButton Uni Microphone Appendix D AccessoriesAppendices ~ Appendix D Accessories Accessory ClearOne Part NumberExample Appendix E Serial CommandsCommand structure ConventionsUnit type Appendices ~ Appendix E Serial CommandsGroups and channels Type and device IDsError number Text message Explanation/Solution Serial command error codesMeter type definitions Command Function XAP 800 Serial commandsSelects/reports phantom power setting Selects/reports NOM setting on outputSelects/reports off attenuation mode for Selects PA adapt mode for specified inputArgument details Aamb Adaptive Ambient ModeAEC Acoustic Echo Canceller Enable/Disable AGC Automatic Gain ControlAmblvl Ambient Level Adjust Agcset Automatic Gain Control Adjust100 Cgroup Compressor Group Select Chairo Chairman Override Mode101 Baud Baud RateGain of 3dB Compress Compressor Adjust102 Compsel Compression Select103 Decay Decay AdjustDelay Delay Adjust Delaysel Delay SelectDspver DSP Version Dfltm Default Meter104 Did Device IDName Description Units Filter Filter Adjust105 ExamplesFlow Flow Control FMP First Mic Priority Mode106 Filtsel Filter SelectButton assignment Gain Gain Adjustment107 FPP Front Panel PasscodeExample GHOLD- Gate Hold Time Adjust108 Gate Gate StatusGover Gating Override Gmode Gating ModeGratio Gate Ratio Adjust 109Label Label 110Greport Gate Report Grpsel Gating Group SelectLFP Lock Front Panel LMO Last Mic On ModeLock Preset and Macro Lock 111LVL Level Lockprst Apply the lock to a preset or macroLockpwd Set preset/macro password 112= Toggle 113Lvlreport Level Report Lvlrrate Level Report RateMacro Macro Execution/Reporting Master Expansion Bus Master ModeMAX Maximum Gain Setting 114MIN Minimum Gain Setting Mdmode Modem Mode115 116 Minmax Minimum and Maximum Gain SettingMinit Modem Initialization String 117 Mline Mic/Line AdjustMpass Modem Password CommandSRC = source Dest = destination Chnl = channel GRP = group Mtrxlvl Matrix Attenuation Adjustment118 Mtrx MatrixMute Mute NCD Noise Cancellation DepthNcsel Noise Cancellation Select 119120 NLP Non-Linear Processing AdjustNOM Number of Open Microphones Mode Offa Off Attenuation ModeCommand Channel Select mic input Value PAA PA Adaptive ModePP Phantom Power Preset Preset Execution/ReportingString location 122Prgstring Program String Supported special charactersName Description Unit Ramp Ramp Gain Adjustment123 Refsel PA/AEC Reference SelectSerecho Serial Echo Refset Reference channel setupSermode Serial Mode 124Siggen Signal Generator Sftymute Safety mute125 String String Execution Sigtout Signal Generator Time OutSlvl Speech Level Control Enable/Disable 126VER Version 127Tout Time Out Select UID Unit ID128 Appendix F Warranty129 Appendices ~ Appendix F WarrantyFCC Part 15 Compliance Safety Information130 Appendix G ComplianceGlossary 131Glossary 132133 134 135 136 137 138 139 Signal Delay Used forIndex 14033-35 Index 141Frequency response 142143