1.Remove Unit front lower access panel as instructed for access to carbonator secondary CO2 regulator with 100-psi gage.

2.Observe pressure setting on carbonator secondary CO2 regulator gage.

3.To lower CO2 pressure, loosen regulator adjusting screw lock nut. Turn adjusting screw to the left (counterclockwise) until pressure gage reads 15-psi below desired reading, then turn screw to the right

(clockwise) until gage reads desired pressure. DO NOT SET CO2 REGULATOR PRESSURE BELOW 25-PSI HIGHER THAN PRODUCT BLENDER TANKS CO2 REGULATORS ARE ADJUSTED TO (SEE PRECEDING IMPORTANT NOTE). Tighten adjusting screw lock nut after each adjustment.

4.To raise CO2 pressure, turn regulator adjusting screw to the right (clockwise) until gage reads desired pressure. DO NOT SET PRESSURE HIGHER THAN 60-PSI. Make sure primary CO2 regulator on CO2 cylinder is set at 80 to 100-psi. Tighten adjusting screw lock nut after each adjustment.

5.Install Unit front lower access panel by reversing removal procedure.

ADJUSTING BEATER MOTOR CURRENT (EITHER SIDE)

Adjusting beater motor current (either side) procedure is very important and must be performed as instructed. Be sure you fully understand the instructions before performing the current adjustments or doing any preventative maintenance current readings check.

Any current adjustments or preventative maintenance current readings check on the beater motor current (either side) must be performed with both freeze cylinders fully defrosted. A partially defrosted freeze cylinder will cause false current readings to be displayed on the message display. Adjust beater motor current (either side) as follows:

1.Place No. 4 ‘‘BEATER MOTOR CURRENT READOUT’’ switch on DIP SWITCH assembly on master circuit board (see Figure 10) in ‘‘ON’’ position. Both freeze cylinders beater motors will start and operate and beaters motors current ratings will be displayed on message display.

2.Display should be adjusted to read A150 B150 ± 2 by adjusting MOTOR CURRENT ADJUSTMENTS located on No. 1 and No. 2 relay circuit boards (see Figure 10). These figures will fluctuate slightly with variations in line voltage and motor loads.

3.After completion of adjusting beater motor current to A150B150 ± 2, make sure No. 5 ‘‘MOTOR CURRENT SELF-CALIBRATION’’ switch on DIP SWITCH assembly on master circuit board (see Figure 10) is in ‘‘OFF’’ position. No. 5 switch in ‘‘OFF’’ position allows the ‘‘MOTOR CURRENT’’ SELF-CALIBRATION’’ electronics to automatically self calibrate the beaters motors currents at completion of each defrost cycle.

CAUTION: IF NO. 4 ‘‘BEATER MOTOR CURRENT READOUT’’ SWITCH ON DIP SWITCH assembly is placed in ‘‘ON’’ position and beater motor current readings were A155B145 and switch was then placed back in ‘‘OFF’’ position without readjusting to A150B150 ± 2, beater

motor current has just been reset at A155B145. Operating the FCB Dispenser at these current readings may have serious effects on its operation.

ANY TIME THE NO. 4 ‘‘BEATER MOTOR CURRENT READOUT’’ SWITCH ON DIP SWITCH ASSEMBLY IS PLACE IN ‘‘ON’’ POSITION, THE BEATER MOTOR CURRENT READINGS MUST BE READJUSTED TO A150B150 ± 2 AS INSTRUCTED, THEN SWITCH MUST BE PLACE BACK IN THE ‘‘OFF’’ POSITION.

ADJUSTMENTS, AND PROGRAMMING MAIN MENU SELECTIONS INTO UNIT

NOTE: The Unit control panel switches are as shown in Figure 9.

The following instructions outline adjustments and programming main menu selections, components ‘‘DIAGNOSE’’ (DIAGNOSTIC MODE), and ‘‘TOTALS’ (DISPLAYED CYCLES AND HOURS TOTALS) into the Unit.

NOTE: Plain water, CO2 and syrup supplies to Unit must be satisfied to turn off ‘‘H2O OUT’’, ‘‘CO2 OUT’’, ‘‘SYRUP 1’’, and ‘‘SYRUP 2’’ fault messages on message display before adjustments and programming procedures can be performed on the Unit.

326142000

36

Page 42 Page 44
Page 43
Image 43
Cornelius 326142000 service manual ADJUSTMENTS, and Programming Main Menu Selections Into Unit
Page 42 Page 44

326142000 specifications

Cornelius 326142000 is an innovative and cutting-edge device that has garnered significant attention in the tech world due to its unique features and capabilities. Designed with a focus on functionality and efficiency, this model represents a significant leap forward in its category.

At the heart of Cornelius 326142000 is a powerful processor that ensures seamless multitasking and high performance. With advanced processing capabilities, it can handle complex tasks effortlessly, making it ideal for users who require both speed and efficiency. Whether for professional applications or daily activities, this device promises to meet diverse needs.

The design of the Cornelius 326142000 is both sleek and user-friendly. Its ergonomic design allows for comfortable usage, while the lightweight build enhances portability. The device is equipped with a high-resolution display that delivers vibrant colors and crisp details, providing an immersive visual experience. This is particularly appealing for tasks that require precision, such as graphic design or video editing.

In terms of connectivity, Cornelius 326142000 includes various options. It features advanced wireless technologies, such as Bluetooth 5.0 and Wi-Fi 6, ensuring fast and reliable connections. This makes it suitable for users looking to stay connected, whether in a work environment or at home.

The device integrates cutting-edge security features to protect user data. With biometric authentication options such as fingerprint scanners and facial recognition, users can rest assured that their information is secure. Additionally, regular firmware updates and built-in antivirus systems enhance its overall security.

Another standout characteristic is its energy efficiency. Cornelius 326142000 incorporates the latest power-saving technologies, allowing it to operate for extended periods without compromising performance. This aspect is particularly beneficial for users who are often on the go and need a device that can keep up with their lifestyle.

Lastly, the Cornelius 326142000 supports a range of software applications, offering versatility for users across different industries. Whether for education, business, or entertainment, the device's compatibility with various programs makes it a valuable tool for productivity.

In summary, the Cornelius 326142000 is a remarkable device that combines robust performance, sleek design, and advanced technologies, making it an excellent choice for anyone seeking reliability and efficiency in their tech gadgets.
Top Page Image Contents