Craftsman 139.3043 owner manual Door Control

Features(Continued)

USING YOURGARAGEDOOROPENER

The garagedoor opener can be activatedthrough a wall-mounted door control, remote control, wireless keyless entry or AssureLinkTM accessory.

When the door is closed and the garagedoor opener is activated the door will open. If the door senses an obstruction or is interrupted while opening the door will stop. When the door is in any position other than closed and the garage door opener is activated the door will close. If the garage door opener senses an obstruction while closing, the door will reverse. If the obstruction

interrupts the sensor beam the garagedoor opener lights will blink 10 times. However,you can close the door if you hold the button on the door control or keylessentry until the door is fully closed. The safety reversing sensors do no effect the opening cycle.

The safety reversing sensor must be connected and aligned correctly before the garagedoor opener will move in the down direction.

Door Control

USINGTHE DOORCONTROL

Push Bar

Screen

Navigation

Buttons

Motion

Sensor

LIGHT

Button

Push Bar

Pressthe push bar to open or close the door.

Light Button

Pressthe LIGHT button to turn the garagedoor opener lights on or off. When the lights are turned on they will stay on until the LIGHT button is pressedagain, or until the garage door opener is activated. Oncethe garagedoor opener is activatedthe lights will turn off after the specified period of time (the factory setting is

4-1/2 minutes). The LIGHTbutton will not control the lights when the door is in motion. The duration of the light timing can be adjusted using the door control.

Navigation Buttons

Usethe navigation buttons to make selections and program features.

Screen

The screen will display the time and temperature until the menu button is pressed, and then it will display the menu options. If there is a problem with the garagedoor opener the screen will display the Diagnostic Code. Referto the Troubleshooting section.

The followingfeatures are accessiblethroughthe screen using the navigationbuttonson the Smart Control Panel:

LEARNA DEVICE

Any compatible remote controls, wireless keylessentry, or AssureLinkTM accessories can be programmed to the garagedoor opener by accessing the menu and using the navigation buttons on the Smart Control Panel.

Lock

The LOCKfeature is designed to preventactivation of the garage door opener from remote controls while still allowing activation from the door control and keylessentry. This feature is useful for added peaceof mind when the home is empty (i.e. vacation).

Timer-to-Close(TTC)

DO NOTenableTTC if operating a one-piece door. TTC is to be used ONLYwith sectional doors.

Factory default is set to off. TTC can be set to automatically close your garagedoor from the fully open position after a specified period of time (1, 5, 10 minute intervals). The Smart Control Panel also has a custom setting up to 99 minutes. The garage door opener will beep and the lights will flash before closing the door. The screen on the door control will display the status of the TTC such as time to close, paused,or an error. If the door encounters an obstruction while closing, the garagedoor opener will make a second attempt to close the door. If the obstruction has not been cleared after the second attempt, the garagedoor opener will reverse open, stop and WILL NOTclose until the obstruction has been cleared. TTCWILL NOTwork if the garage door opener is operating by battery power or if the safety reversing sensors are misaligned. This feature is NOTintended to be the primary method of closing the door. A keyless entry shouldbe installed in the event of an accidental lock out when usingthis feature.

AUTOMATICLIGHT

Motion Sensor

Factory default is set to on. This feature will automatically turn on the garagedoor opener lightswhen motion is sensed.The lights will come on for the set period of time, then shut off.

The lightswill turn on when someone enters through the open

garage door and the safety reversing sensor infrared beam is broken.

If using the garagedoor opener light as a work light disable the Automatic Light Feature,otherwise the light will turn off automatically if you are beyond the rangeof the sensor.

32