"FinalAdjustments" section of the Assembly Instructions.

WARNING: The electric starter must be properly grounded at all times to avoid the possibility of elec- tric shock which may be injurious to the operator.

Determine whether your house wiring is a three- wire grounded system. Ask a licensed electrician if you are not certain.

,_

not a three-wire grounded system, do not use

WARNING: If your house wiring system is

 

this electric starter under any conditions.

If your house wiring system is grounded and a three-hole receptacle is not available at the point the snow thrower starter will normally be used, one should be installed by a licensed electrician. When connecting the power cord, always connect cord to starter on engine first, then plug the other end into a three-hole grounded receptacle.

When disconnecting the power cord, always unplug the end from the three-hole, grounded receptacle first.

Attach spark plug wire to spark plug.

Make sure that the auger drive and the traction drive levers are in the disengaged RELEASED position.

Move throttle control lever to FAST position.

Remove the keys from the plastic bag. Push key into the ignition slot. Make sure it snaps into place. Do not turn key. Keep the second key in a safe place.

Rotate the choke knob to FULL choke position.

Connect the power cord to the switch box on the engine.

Plug the other end of the power cord into a three-hole, grounded 120 volt A.C. receptacle.

starting the engine with an electric starter.

,_. WARNING: Do not use primerwhile

Push down on the starter button until the engine starts. Do not crank for more than 10 seconds at a time. This electric starter is thermally protected. If overheated, it will stop automatically and can be restarted only when it has cooled to a safe temperature (a wait of about 5 to 10 minutes is required).

When the engine starts, release the starter button and slowly rotate the choke to OFF position. If the engine falters, rotate the choke to FULL and then gradually to OFF.

Disconnect the power cord from the receptacle first and then from the switch box on the engine. Allow the engine to warm up for a few minutes because the engine will not develop full power

until it reaches operating temperature.

Operate the engine at full throttle (FAST) when throwing snow.

Warm Start

If restarting a warm engine after a shut down, rotate choke to OFF instead of FULL and press the starter button.

B. Recoil Starter

Make sure that the engine has sufficient oil and the auger drive and the traction drive levers are released.

Move throttle control to FAST position.

Push key into the ignition slot so that it snaps into place. Do not turn key. Remove plastic bag and keep the second key in a safe place.

Rotate choke control to FULL choke position.

Push the primer button while covering the vent hole. Remove your finger from the primer between primes. Do not prime if temperature is above 50oF; prime two times between 50o F and 15° F; and prime four times below 15oF.

Pull the starter handle rapidly. Do not allow the handle to snap back, but allow it to rewind slowly while keeping a firm hold on the starter handle. As the engine warms up and begins to operate evenly, rotate the choke knob slowly to OFF position. If the engine falters, return to FULL choke, then slowly move to OFF choke position.

Allow the engine to warm up for a few minutes because the engine will not develop full power until it reaches operating temperature.

Operate the engine at full throttle (FAST) when throwing snow.

Warm Start

If restarting a warm engine after a temporary shut down, rotate choke to OFF instead of FULL and do not prime. Press the starter button.

Frozen Recoil Starter

If the starter is frozen and will not turn the engine, proceed as follows:

Pull as much rope out of the starter as possible.

Release the starter handle and let it snap back against the starter.

If the engine still fails to start, repeat the first two steps. If continued attempts do not free starter, follow the electric starter procedures to start. Avoid possible freezing of recoil starter and the engine controls.

Operating Snow Thrower

To Engage Drive

With the engine running near top speed, move shift lever to one of six FORWARD positions or

15

Page 15
Image 15
Craftsman 247.88851 owner manual Operating Snow Thrower, Warm Start, Frozen Recoil Starter

247.88851 specifications

The Craftsman 247.88851 is a standout lawn mower, designed to meet the needs of homeowners looking for a reliable and efficient gardening solution. This model combines innovative features with user-friendly technology to provide an exceptional mowing experience. Its power and performance are backed by a robust 21-inch cutting deck, making it ideal for tackling small to medium-sized yards with precision.

One of the notable features of the Craftsman 247.88851 is its 140cc engine. This engine offers sufficient power to handle various grass types and conditions, ensuring a clean and even cut every time. The starting mechanism boasts a reliable pull-start system, simplifying the operation and enhancing user convenience. This model also incorporates a 5-position height adjustment feature, allowing users to customize their mowing height according to their lawn's specific needs.

The Craftsman 247.88851 stands out with its ease of maneuverability. Its lightweight design and compact frame facilitate effortless navigation around obstacles such as trees and garden beds. The lawn mower is equipped with 7-inch front wheels and 8-inch rear wheels, providing excellent stability and traction. This stability is crucial for achieving optimal mowing results, especially on uneven terrain.

Another remarkable technology featured in the Craftsman 247.88851 is its superior grass collection system. The mower comes with a 1.9-bushel grass bag that efficiently collects clippings, ensuring a tidy lawn finish. Alternatively, users can opt for mulching functionality, which finely cuts and distributes the clippings back into the lawn, promoting healthy growth and providing essential nutrients.

In terms of build quality, the Craftsman 247.88851 is constructed with durable materials that withstand the rigors of regular use. Its sturdy design minimizes vibrations, resulting in a smoother mowing experience while reducing operator fatigue.

Overall, the Craftsman 247.88851 is an excellent choice for homeowners seeking a powerful, efficient, and easy-to-use lawn mower. Its combination of a strong engine, precise cutting capabilities, and advanced features makes it a valuable addition to any garden maintenance toolkit. Whether tackling overgrown patches or maintaining a well-groomed lawn, this mower delivers consistent and reliable performance.