Craftsman 316.79197 manual Safety and International Symbols, Unladed, On/Off, Away

positionwhilestartingReferto.Starting/Stopping Instructions.

•Use the right tool. Only use this tool for its intended purpose. Do not overreach. Always keep proper footing and balance.

Always hold the unit with both hands when operating. Keep a firm grip on both handles or grips.

Keep hands, face, and feet at a distance from all moving parts. Do not touch or try to stop the cutting attachment when it rotates.

Do not touch the engine, gear housing or muffler. These parts get extremely hot from operation, even after the unit is turned off.

Do not operate the engine faster than the speed needed to cut, trim or edge. Do not run the engine at high speed when not cutting.

Always stop the engine when cutting is delayed or when walking from one cutting location to another.

If you strike or become entangled with a foreign object, stop the engine immediately and check for damage. Do not operate before repairing damage. Do not operate the unit with loose or damaged parts.

Stop the unit, switch the engine to off, and disconnect the spark plug for maintenance or repair.

Use only replacement parts or accessories recommended for this tool that are distributed by Sears or a Craftsman outlet.

Use of any replacement parts or accessories purchased elsewhere may be hazardous, and will also void your warranty.

Keep unit clean of vegetation and other materials. They may become lodged between the cutting attachment and shield.

To reduce fire hazard, replace a faulty muffler and spark arrestor. Keep the engine and muffler free from grass, leaves, excessive grease or carbon build up.

OTHER SAFETY WARNINGS

Never store the unit with fuel in the tank, inside a building where fumes may reach an open flame (pilot lights, etc.) or sparks (switches, electrical motors, etc.).

Allow the engine to cool before storing or transporting. Be sure to secure the unit while transporting.

Store the unit in a dry area, locked up or up high to prevent unauthorized use or damage, out of the reach of children.

Never douse or squirt the unit with water or any other liquid. Keep handles dry, clean and free from debris. Clean after

each use, see Cleaning and Storage Instructions.

Keep these instructions. Refer to them often and use them to

instruct other users. If you loan someone this unit, also loan them these instructions.

SAVE THESE INSTRUCTIONS

• SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product. Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.

SYMBOL			MEANING
,_,		=	SAFETYIndicates ALERTdanger, SYMBOLwarning or caution. May
			be used in conjunction with other symbols or
		; WARNING i READ OPERATOR,S MANUAL
ill I	I!11		Readtheoperator'smanual(s)andfollowall
I _L.	r	J warnings and safety instructions. Failure to do
			so can result in serious injury t° the operato r
			and/or bystanders
			WEAREyEANDNEARINGPROTECT O"
Ir_,A1			WARNING:		Thrown objects and loud noise
			can cause severe eye injury and hearing 10s&
			Wear eye protection meeting ANSI Z8711
			standards and ear protection when operating
			this unit. Use a full face shield when needed.
		"	UNLADED		FUEL
_l			AlwaYS use ciean' t[esh unleaded rue!
	_		Refer	tOoperato r S manua If°r the proper
			type	of o.

SYMBOL MEANING

!" ON/OFFSTART/RUNSTOP CONTROL

t	•	ON/OFF	STOP CONTROL
		OFF or STOP
A	•	KEEP BYSTANDERS				AWAY
,_;;;,,_		WARNING:		Keep all bystanders, especially
		children and pets, at least 50 feet (15 ml
		from the	operating		area.
_"_ O	•	THROWN	OBJECTS AND ROTATING
_/7_1_		CUTTER CAN CAUSE SEVERE INJURY
/ _/--_		WARNING:		Do not	operate without		the
//,in		cutting attachment			shield in place.		Keep
__-_T _		away from		the rotating		cutting attachment.
	o SHARP BLADE
		WARNING: Sharp blade on cutting
--___lr		attachment		shield.	To prevent serious injury,

do not touch the line cutting blade.

,,NOT SURFACE WARNING

Do not touch a hot muffler, gear housing or cylinder. You may get burned. These parts get extremely hot from operation. They remain hot for a short time after the unit is turned off.