Manuals / Craftsman / Lawn and Garden / Snow Blower

Craftsman 536.88626 operating instructions Handle Upper, Washer Sptlk

Models: 536.88626

1 54

Download 54 pages 9.11 Kb

Page 41

Image 41

CRAFTSMAN 26" 9HP SNOW THROWER 536.886260

HANDLE ASSEMBLY

Key No.				Description			Part No.
720	HANDLE,		UPPER				9552-853
724	SCREW,	5/16-18X2.75					11234
725	WASHER,		FLAT .349X.69X.066				71071
726	WASHER,		SPTLK		.31X.58X.08		71060
727	NUT, 5/16-18			REGHEX			71037
728	STOP, RED PLASTIC						11261
73O	SET OF CLUTCH				HANDLE	LH & RH	334195
731	SET OF CLUTCH				HANDLE	LH & RH	334195
733	PIN, CLUTCH			HANDLE			4140
734	NUT, PUSH ON CAP						3535
739	BUMPER,		RECTANGLE				4049
740	CABLE,	CLUTCH			28.44L		1579
741	CABLE,	AUGER			CLUTCH		761590
743	TENSION		SPRING				579869
744	SPRING,		AUGER		CLUTCH		1673
745	NUT, 1/4--20						780029
746	BOOT, CLUTCH				SPRING		308146
750	HANDLE,		LOWER				339541-853
751	SCREW, 5/16-18 Xl.00						313053
752	WASHER,		SPTLK				71060
753	NUT, 5/16-18			REGHEX			71037
754	PUSHNUT, 5/16				BOLT RETAINER		309436
755	BRKT, GEAR			SELECTOR			337407--853
756	SCREW,		5/1 6-18X2.00				6751
757	SCREW,		.25X.75X.51				300303
F-O01088J					41

Page 41

Image 41

Craftsman 536.88626 operating instructions Handle Upper, Washer Sptlk

Contents

001088J Snow ThrowerWash Hands After Handling Preparation TrainingSlow Fast Electric Start Engine Start Engine Run Maintenance and StorageDrive Clutch Reverse Auger Clutch Auger Collector Engage ÷61Not actual size Thrower Tools Required for AssemblyTo Remove Snow Thrower From Carton ShifterRemove To Assemble the Handle and Crank AssemblyLoosen Knob To Install Shifter KnobShort LongHOW to SET the Length of the Cables Snow Chute AssemblyHOW to SET the Skid Height Position snow chute on insideDown Know Your Snow ThrowerChoke Control Used to start a cold To Stop Your Snow Thrower HOW to Move Forward and BackwardTo Control Snow Discharge To USE Wheel Lockout PINBefore Starting the Engine Service & Adjustments section of this manualCheck the OIL Fill GASTo Stop Engine Equipped with a three-wireTo Start Engine Cold StartWarm Start Run engine at full throttle Fast when throwing snowCold Start Warm StartSnow Throwing Tips Customer Responsibilities Lubrication ChartManual After Each USEAS Required Product SpecificationsLUBRICATION-EVERY 25 Hours LUBRICATION-NOT RequiredLubrication EngineTo Change Engine OIL Spark PlugTo Adjust Skid Height To Adjust Scraper BARRemove the belt cover. See HOW to Check and Adjust CablesTo Adjust Belts To Replace Belts Traction Drive BeltOutdoors, away from fire or Auger DriveTraction DriveAuger Pulley is properly aligned with the traction drive beltOutdoors, away from fire or Arning Drain the gasoline flame HOW to Adjust the Belt Guide HOW to Adjust or Replace the Friction WheelIf an adjustment is necessary, loos Is not in the correct position, adjust as followsOutdoors, away from fire or How To Replace The Friction WheelTo adjust To Adjust or Replace the SparkplugHOW to Replace the Auger Shear Bolt 001088J27 Line outdoors, away from OtherSnow Thrower Correction TroubleCause Description Craftsman 26 9HP Snow Thrower 536.886260 Frame AssemblyScrew Electric Start AssemblyMotor Starter Frame Assy Frame AssemblyGear Case Assembly Craftsman 26 9HP Snow Thrower 536.886260 Drive Components Flatwasher Drive500 Auger Housing Assembly5OO 544Craftsman 9HP Snow Thrower Auger Housing Assembly593 582 Plastic Craftsman 26 9HP Snow Thrower Discharge Chute Assembly725 Handle AssemblyWasher Sptlk Handle UpperWasher 678 673 Wheel Assembly8OO Shift Yoke Assembly874 Chute Control ROD Assembly863 867 828 831 Decals824 View from AugerCraftsman 4-CYCLE Engine Model Number KEY Part Description Craftsman 4-CYCLE Engine Model NumberGasket Piston, Pin & Ring Set28820 298Incl EI6 40-J KEY Part 31J Craftsman 4-CYCLE Engine Model Number 8tAR8

CRAFTSMAN 26" 9HP SNOW THROWER 536.886260

HANDLE ASSEMBLY

Description

HANDLE,

UPPER

SCREW,

WASHER,

WASHER,

SPTLK

.31X.58X.08

71060

CABLE,