Craftsman 917.28928 Troubleshooting Chart, clicks but, will not, Loss of power, continues

Models: 917.289283 917.28928

1 64
Download 64 pages 7.66 Kb
Page 30
Image 30
clicks but

TROUBLESHOOTING CHART:

See appropriate section in manual unless directed to Sears service center

PROBLEM

 

CAUSE

 

 

 

 

 

 

 

CORRECTION

 

 

Engine

clicks but

1

Weak

or dead

battery.

 

1

Recharge

or

 

replace battery.

will not

start

2

Corroded

battery

terminals.

2

Clean

battery

terminals.

 

 

 

 

 

 

3

Loose

or damaged

wiring.

 

3

Check

 

all wiring.

 

 

 

 

4

Faulty

solenoid

or starter.

 

4

Check/replace

 

solenoid

or starter.

Loss of power

1

Cutting

too

much

grass/too

fast.

1

Raise

cutting

 

height/reducespeed.

 

 

2

Throttle

 

in "CHOKE" position.

2

Adjust

throttle

control.

 

 

 

3

Build-up

 

of grass,

leaves

and

3

Clean

underside

of mower

 

 

 

trash

under

mower.

 

 

housing.

 

 

 

 

 

 

 

4

Dirty

air

 

filter.

 

 

 

4

Clean/replace

 

air

filter.

 

 

 

5

Low oil

level/dirty

oil.

 

5

Check

 

oil

level/change

oil.

 

 

6

Faulty

spark

plug.

 

 

6

Clean

& regap

or change

spark plug.

 

 

7

Dirty

fuel

filter.

 

 

 

7

Replace

fuel

 

filter.

 

 

 

8

Stale

or

 

dirty fuel.

 

 

8

Empty fuel tank and refill tank with

 

 

 

 

 

 

 

 

 

 

 

 

fresh,

clean

gasoline.

 

 

 

 

Water

in fuel.

 

 

 

9

Empty fuel tank and carburetor,

 

 

 

 

 

 

 

 

 

 

 

 

refill tank with fresh gasoline and

 

 

 

 

 

 

 

 

 

 

 

 

replace

fuel

filter.

 

 

10Spark plug wire loose.

11Dirty engine air screen/fins.

12Dirty/clogged muffler.

13Loose or damaged wiring.

14Carburetor out of adjustment.

15Engine valves out of adjustment.

Excessive vibration

1

Worn, bent or loose blade.

2Bent blade mandrel.

3Loose/damaged part(s).

Engine

continues

to

Faulty

operator-safety

presence

run when operator

 

control

system.

 

leaves

seat with

atta=

 

 

 

chment

clutch engaged

 

 

 

Poor

cut

= uneven

1

Worn,

bent or loose

blade.

cutting

2Mower deck not level.

3Buildup of grass, leaves, and trash under mower.

4Bent blade mandrel.

5Clogged mower deck vent from

build-up of grass, leaves, and trash around mandrels.

10Connect & tighten spark plug wire.

11Clean engine air screen/fins.

12Clean/replace muffler.

13Check all wiring.

14See "To Adjust Carburetor" in Service and Adjustments section.

15Contact a Sears or other qualified service center.

1Replace blade. Tighten blade bolt.

2Contact a Sears or other qualified service center.

3Tighten loose part(s). Replace damaged parts.

Check wiring, switches and connections. If not corrected, contact a Sears or other

1Replace blade. Tighten blade bolt.

2Level mower deck.

3Clean underside of mower housing.

4Contact a Sears or other qualified service center.

5Clean around mandrels to open vent holes.

30

Page 30
Image 30
Craftsman 917.289283 owner manual Troubleshooting Chart, clicks but, will not, Loss of power, continues