Manuals / Brands / Computer Equipment / Personal Computer / CyberResearch / Computer Equipment / Personal Computer

CyberResearch CPEN GX-333-X External Interfaces, Version, Figure 2-5 Version 1.10 External Interfaces (Component Side)

1 98

Download 98 pages, 1.55 Mb

CPEx GX-333-X

CyberResearch® CPU Cards

External Interfaces

For the locations of external interfaces, please refer to the diagram below:

Figure 2-5 Version 1.10 External Interfaces (Component Side)

22	©Copyright 2007 CyberResearch, Inc.

Contents

CPEx GX-333-X VER. 1.21 • APR No part of this manual may be reproduced without permission Page Page Page Page Intentionally Blank Packing List System Monitoring CPU Memory VGA/LCD Interface Page Page Introduction Product Overview General Information Page Connectivity Page CPEx GX-333-XBoard Overview Technical Specifications Serial Ports Parallel Port Audio Connector USB Interface Watchdog Timer Packing List System Monitoring Functional Description CPU, Memory, and VIA Chipsets CPU Memory VGA/LCD Interface Audio Block Diagram Important Features External Interfaces Page NOTE: Chapter 3: Installation Chapter 3 Installation Table 2-3Interface Connectors 2-pinconnector to an onboard Lithium coin cell battery SDRAM DDR SO-DIMMsocket (on the soldering side) Internal Connectors 1.CN1: -5V& -12VSupplementary Power Connector This connector provides a –5Vand a-12Vinput pins. These two minus voltage pins connect to the identical pins on ISA bus golden fingers Table 2-4CN1: -5V& -12VConnector Pinouts Table 2-6CN3 SBVCC: ATX Power Feature Pinouts PIN 1GND 2PS_ON 5VSB Table 2-9CN6 Chassis LED Connector Pinouts LED+ (VCC) LED- (GND) IDE_LED+ (VCC) IDE_LED 9. CN8: Fan Connector Table 2-12CN8 Fan Connector Figure 2-17CN8 Fan Connector 10.CN9: Floppy Connector Table 2-13CN9: Optional Floppy Connector 11. CN10: Flat Panel (TTL/TFT) Display Connector Table 2-14CN10 – TTL LCD Flat Panel Connector Pinouts TFT_B7 Figure 2-19CN10 TTL LCD Panel Display Connector 12. CN11: IDE Connector Table 2-15CN11 IDE Connector Pinouts PIDE_RST# PIDE_D7 PIDE_D8 Table 2-16CN12 & CN13 USB Port Pinouts USB_GND D1F USBDT3P USBDT2P Table 2-17CN14 Coin Cell Battery Connector Pinouts 1+3V 2GND Figure 2-22CN14 Battery Connector 15.CN15: IrDA Port 17.CN17: Parallel Port Connector Table 2-20CN17Parallel Port Pinouts Figure 2-25CN17 Parallel Port 18.CN18: COM2/3 Internal Serial Port Table 2-21CN18: 14 (2x7) Pin 2.0mm Connector Pinouts Figure 2-26CN18: COM2/COM3 Serial Port Figure 2-27COM2/COM3 Serial Port Adapter Cable 19.CN19: Audio Port Connector Table 2-22CN19 Audio Port Pinouts Figure 2-28CN19 Audio Port Connector 20.CN20: Optical Drive Audio LINE_IN Table 2-23CN20 Audio LINE_IN Pinouts Figure 2-29CN20 Audio LINE_IN 21.CN25: KB/MS Connector Table 2-24CN25 KB/MS Connector Pinouts VCC_KM MS_DATA MS_CLK 23.CN28: Compact Flash Connector) Table 2-26CN28 Pinouts VCC-INCHECK1 DATA3 DATA11 Rear Slot Bracket Connectors 3. Ethernet Port LED Indicators CN22 Ethernet Port LED Indications SPEED LED ACT/LINK LED Status Installation Considerations Prior to Installation Preparing Your SBC Installation Notices Airflow Consideration Unpacking Precautions Memory Module Jumper Settings PIN STATE Select Panel 2 – 3 (Default) Select CRT JP2: (AT/ATX Mode Selector) JP6: Flat Panel TTL (CN10) Clock using select Table 3-4JP6 Pin Configurations JP6 Short 1 – Default Installation Optional Floppy Drive Connector (CN9) Connecting the Floppy Drive Compact Flash Disk Parallel Port Connector (CN17) Audio Interface Audio Connector COM Port Connectors [COM1(CN21), COM2/COM3(CN18)] LCD Flat Panel Connection (CN10,) Chapter 2 Functional Accessories Included in Kit Page Award BIOS Setup Introduction Starting Setup Using Setup Getting Help Unable to Reboot After Configuration Changes Standard CMOS Features: Advanced BIOS Features: Advanced Chipset Features: Integrated Peripherals: Power Management Setup: Standard CMOS Features Page Page ÎCPU Internal (L1 & L2) Cache [Enabled] CPU L1 & L2 Cache Disabled ÎSATA Boot ROM Control Appendix C Boot Other Device ÎSwap Floppy Drive [Disabled] ÎBoot Up Floppy Seek [Enabled] Disabled (DEFAULT) ÎBoot Up Numlock Status [On] ÎGate A20 Option Îx Typematic Delay (Msec) [250] Typematic Delay ÎSecurity Option [Setup] Security Option Advanced Chipset Features Integrated Peripherals ÎIDE Primary Master/Slave UDMA [Auto] ÎIDE DMA transfer access [Enabled] IDE DMA transfer access ÎIDE HDD Block Mode [Enabled] IDE HDD Block Mode ÎUART Mode Select [Normal] ÎOnboard Parallel Port [378/IRQ7] SPP EPP ECP Page ÎACPI Mode ÎLegacy Mode Standby Mode Suspend Mode ÎMODEM Use IRQ PnP/PCI Configurations IRQ Resources PCI Device (DEFAULT) Reserved ÎMemory Resources [Press Enter] ÎPCI/VGA Palette Snoop [Disabled] Page Watchdog Timer INT 15H: AH – 6FH Example program: ;INITIAL TIMER PERIOD COUNTER ;ADD YOUR APPLICATION PROGRAM HERE ; EXIT ; Page Connecting ATX Power Supply The following notes show how to connect ATX Power Supply to the embedded board 1.Using ATX Power Switch Step Figure B-34ATX Power Connection 2.Using AT Power Supply Page ALi® RAID for SATA 1.1.1 1. Introduction CAUTION Chapter 4 Award BIOS Setup 1.Boot ->Onboard SATA ROM 2.Chipset ->Southbridge Chipset Configuration 1.1.32. Features and Benefits 3. SATA-ALiRAID Driver ALi SATA Controller Driver Installation Steps - During Windows XP Installation step Installation Steps under Existing Windows XP Step1 1.1.5 4. Accessing the ALi RAID Utility Press Ctrl-Ato enter ALi RAID BIOS setup utility 1.RAID BIOS Setup Menu: 2.RAID Options: 2.1Create RAID0 Striping for Performance WARNING Page 2.2Create RAID1 Mirroring for Reliability 2.3Create JBOD for Integrated Capacity 2.4Stripe Size 2.5Delete RAID Setting & Partition 2.6Delete All RAID Setting & Partition 2.7Rebuild RAID Array 2.8Select Boot Drive Diagnosis and Debug Page Returns and RMAs PLEASE CALL FOR AN RMA NUMBER Packages returned without an RMA number will be refused Please make sure that the RMA number is prominently displayed on the outside of the box