Cypress CY7C1306BV25, CY7C1303BV25 manual Pin Definitions

CY7C1303BV25

CY7C1306BV25

Pin Definitions

Name

I/O

Description

D[x:0]

Input-

Data input signals, sampled on the rising edge of K and

K

clocks during valid write opera-

Synchronous

tions.

CY7C1303BV25 – D[17:0]

CY7C1306BV25 – D[35:0]

Input-

Write Port Select, active LOW. Sampled on the rising edge of the K clock. When asserted active,

WPS

Synchronous

a Write operation is initiated. Deasserting will deselect the Write port. Deselecting the Write port

will cause D[x:0] to be ignored.

0,

1,

Input-

Byte Write Select 0, 1, 2 and 3 - active LOW. Sampled on the rising edge of the K and

clocks

BWS

BWS

K

BWS2, BWS3

Synchronous

during Write operations. Used to select which byte is written into the device during the current

portion of the Write operations.

CY7C1303BV25 - BWS0 controls D[8:0] and

BWS

1 controls D

[17:9].

CY7C1306BV25 - BWS0 controls D[8:0], BWS1 controls D[17:9], BWS2 controls D[26:18] and BWS3

controls D[35:27]

Bytes not written remain unaltered. Deselecting a Byte Write Select will cause the corresponding

byte of data to be ignored and not written into the device.

A

Input-

Address Inputs. Sampled on the rising edge of the K clock during active Read operations and

Synchronous

on the rising edge of K for Write operations. These address inputs are multiplexed for both Read

and Write operations. Internally, the device is organized as 1M x 18 (2 arrays each of 512K x 18)

for CY7C1303BV25 and 512K x 36 (2 arrays each of 256K x 36) for CY7C1306BV25. Therefore,

only 19 address inputs are needed to access the entire memory array of CY7C1303BV25 and

18 address inputs for CY7C1306BV25. These inputs are ignored when the appropriate port is

deselected.

Q[x:0]

Outputs-

Data Output signals. These pins drive out the requested data during a Read operation. Valid

Synchronous

data is driven out on the rising edge of both the C and C clocks during Read operations or K and

K when in single clock mode. When the Read port is deselected, Q[x:0] are automatically

three-stated.

CY7C1303BV25 - Q[17:0]

CY7C1306BV25 - Q[35:0]

Input-

Read Port Select, active LOW. Sampled on the rising edge of positive input clock (K). When

RPS

Synchronous

active, a Read operation is initiated. Deasserting will cause the Read port to be deselected. When

deselected, the pending access is allowed to complete and the output drivers are automatically

three-stated following the next rising edge of the K clock. Each read access consists of a burst

of two sequential 18-bit or 36-bit transfers.

C

Input-Clock

Positive Input Clock for Output Data. C is used in conjunction with

to clock out the Read

C

data from the device. C and C can be used together to deskew the flight times of various devices

on the board back to the controller. See application example for further details.

Input-Clock

Negative Input Clock for Output Data.

is used in conjunction with C to clock out the Read

C

C

data from the device. C and C can be used together to deskew the flight times of various devices

on the board back to the controller. See application example for further details.

K

Input-Clock

Positive Input Clock Input. The rising edge of K is used to capture synchronous inputs to the

device and to drive out data through Q[x:0] when in single clock mode. All accesses are initiated

on the rising edge of K.

Input-Clock

Negative Input Clock Input.

is used to capture synchronous inputs to the device and to drive

K

K

out data through Q[x:0] when in single clock mode.

ZQ

Input

Output Impedance Matching Input. This input is used to tune the device outputs to the system

data bus impedance. Q[x:0] output impedance are set to 0.2 x RQ, where RQ is a resistor

connected between ZQ and ground. Alternately, this pin can be connected directly to VDDQ, which

enables the minimum impedance mode. This pin cannot be connected directly to GND or left

unconnected.

TDO

Output

TDO pin for JTAG.

TCK

Input

TCK pin for JTAG.

TDI

Input

TDI pin for JTAG.

TMS

Input

TMS pin for JTAG.

Document #: 38-05627 Rev. *A

Page 4 of 19

[+] Feedback