Denon AVR-1610 manual 24

ENGLISH

Getting	Changing the PRE OUT connectors assignment
	(Pre Assign)

Making the Optimum Settings for the Connected Speakers Automatically (Audyssey Auto Setup)

Step 3 : Performing the Audyssey Auto Setup Procedure

Started	The signals output from the AVR-1610’s SURR. BACK / FRONT HEIGHT
	PRE OUT connectors can be switched to signals of the surround mode
Connections
	being used.
	1 Press ui to select “Pre Assign”.
	2 Press o p to select

•The Audyssey Auto Setup function detects the presence of each speaker and automatically calculates the speaker size, channel level, distance, and optimal crossover frequency setting. Audyssey MultEQ corrects acoustical distortions within the listening area.

•Once started, MultEQ will play a series of test tones through each speaker.

•Before starting, connect and position all of your speakers.

5Perform Step 4 repeatedly for the 3rd, 4th, 5th, and 6th measurments.

Once measurements for the sixth position are completed, “All the measurements were finished.” is displayed.

b Measure at a total of six positions, including the main listening

position and positions around it. It is possible to stop the settings

with five positions or fewer, but for better results we recommend

Settings Pre Assign Mode.

1 Press ui to select

3-1.Audyssey Auto Setup MultEQ

measuring at six positions.

Playback	3-1.Audyssey Auto Setup
	MultEQ
	Please place microphone
	at ear height at
	main listening position.
	Front Sp.: A
Remote	Pre Assign:
	Normal
	Start
	Cancel

“Start”, then press

.

Detection of the speaker configuration starts.

Please place microphone at ear height at

main listening position. Front Sp.: A Pre Assign:

Normal Start

Cancel [ENT]:Select [RTN]:Back

6Once measurements are finished, use ui to select “Calculate”,

then press .

Analysis begins.

Step2:Measurement

MultEQ

All the measurements were finished.

Calculate

Retry

Cancel

Control		[ENT]:Select [RTN]:Back
	Normal	: The sound of the surround back channel is output
		from the SURR. BACK / FRONT HEIGHT PRE
Information		OUT connectors.
	Front Height	: The sound of the front height channel is output

Once all the speakers
2 have	been	detected
and	the screen on
the	right	appears,
check the		results

Step1:Speaker Detection

MultEQ

Front Sp. :Yes

Center Sp. :Yes

Subwoofer :Yes

Surround Sp. :Yes

S.Back Sp. :Yes

b Analysis takes several minutes to complete. The time required for this analysis depends on the number of speakers

[ENT]:Cancel

⇩

Step3:Calculating

MultEQ

Calculating Please wait...

from the SURR. BACK / FRONT HEIGHT PRE

of detection of the

Next

:2sp

connected. The greater the number of speakers

OUT connectors.

connected speakers.

Retry

[ENT]:Next

connected, the longer analysis will take.

[----------]

Troubleshooting	n To cancel Audyssey Auto Setup
	Use ui to select “Cancel”, then use o p to select “Yes”.

3Once you have checked the results, use uito select “Next”, then press .

Measurements for the main listening position begin.

Specifications

4Once the screen on the right appears, move the setup microphone to the second position, use

uito select “Next”, then press .

Step2:Measurement

MultEQ

Please place microphone at ear height at

2nd listening position.

Next

Calculate

Cancel

[ENT]:Next

The measurement result				Step4:Check
				MultEQ
confirmation	screen		is	Please check the results
				of the measured item.
displayed.
				Speaker Config.Check
b Subwoofers	or	other		Distance Check
speakers may	be	set	to	Channel Level Check
				Crossover Freq.Check
a value that does not				Next
correspond to	the	actual		[ENT]:Select

distance.

Measurements for the second position begin.

2