ENGLISH
|
|
|
|
|
|
|
|
| Set up speakers (Audyssey® Auto Setup) |
| ||
| About setup microphone placement |
| 1 | Set up | 2 | Set up |
| Simple | ||||
|
|
| version | |||||||||
|
|
|
|
| ||||||||
• Measurements are performed by placing the setup microphone successively at multiple positions |
| the microphone |
| the subwoofer |
| |||||||
|
|
|
| |||||||||
|
|
|
|
|
| |||||||
throughout the entire listening area, as shown in GExample qH. For best results, we recommend you |
| Mount the setup microphone on a |
| If using a subwoofer capable of the |
| |||||||
measure in six positions, as shown in the illustration (up to six positions). |
|
| tripod or stand and place it in the |
| following adjustments, set up | the |
| |||||
• Even if the listening environment is small as shown in GExample wH, measuring at multiple points |
|
|
| |||||||||
| main listening position. |
| subwoofer as shown below. |
|
| |||||||
throughout the listening environment results in more effective correction. |
|
|
|
|
| |||||||
|
| When placing the setup microphone, adjust |
|
|
|
| ||||||
|
|
|
|
|
|
|
| nn When using a subwoofer with a direct | Basic | |||
| GExample qH |
|
|
| GExample wH |
|
| the height of the sound receptor part to the | ||||
| FL SW C | FR |
|
| FL SW C | FR |
| level of the listener’s ear. | mode |
| ||
|
|
|
|
| Set the direct mode to “On” and disable the | version | ||||||
|
|
|
|
|
|
|
| Sound receptor | ||||
|
|
|
|
|
|
|
| setting. |
| |||
|
|
|
|
|
|
|
| Setup | volume adjustment and crossover frequency |
| ||
|
|
|
|
|
|
|
|
|
|
|
| |
( | : Measuring positions) |
|
| ( : Measuring positions) |
| microphone | nn When using a subwoofer without a |
|
| |||
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
| direct mode |
|
| |
|
|
|
|
|
|
|
|
| Make the following settings: |
|
| |
|
|
|
|
|
|
|
|
| • Volume : “12 o’clock position” |
|
| |
|
|
|
|
|
|
|
|
| • Crossover frequency : |
|
| |
|
|
|
|
|
|
|
|
| “Maximum/Highest Frequency” |
|
| |
SL | *M | SR |
| SL | *M | SR |
|
| • Low pass filter : “Off” |
|
| |
|
|
| • Standby mode : “Off” |
| Advanced | |||||||
|
|
|
|
|
|
|
| |||||
FL | Front speaker (L) |
| SW Subwoofer |
|
|
|
|
|
| |||
|
|
|
|
|
|
|
| |||||
FR | Front speaker (R) |
| SL |
| Surround speaker (L) |
|
|
|
|
|
| version |
C | Center speaker |
| SR |
| Surround speaker (R) |
| NOTE |
|
|
| ||
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
| ||
| About the main listening position (*M) |
|
|
|
| • Do not hold the setup microphone in your hand |
|
|
|
| |||
The main listening position is the position where listeners would normally sit or where one would | during measurements. |
|
|
|
| |||||||
• Avoid placing the setup microphone close to a |
|
|
|
| ||||||||
normally sit alone within the listening environment. Before starting Audyssey Auto Setup, place the setup |
|
|
|
| ||||||||
seat back or wall as sound reflections may give |
|
|
|
| ||||||||
microphone in the main listening position. Audyssey MultEQ® uses the measurements from this position |
|
|
|
| ||||||||
inaccurate results. |
|
|
|
| ||||||||
to calculate speaker distance, level, polarity, and the optimum crossover value for the subwoofer. |
|
|
|
| ||||||||
|
|
|
|
|
| |||||||
Information
The “Simple version” describes the installation, connection and setup methods for | 7 |
See page 27 for the installation, connection and setup methods for speakers other than