ENGLISH

Resetting the microprocessor

Perform this procedure if the display is abnormal or if operations cannot be performed. When the microprocessor is reset, all the settings are reset to their default values.

ON/STANDBY

 

 

SURROUND MODE 1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SURROUND MODE 0

1 Turn off the power using ON/STANDBY.2 Press ON/STANDBY while simultaneously pressing SURROUND MODE 0 and

SURROUND MODE 1.

3 Once the display starts flashing at intervals of about 1 second, release the two buttons.

If in step 3 the display does not flash at intervals of about 1 second, start over from step 1.

Specifications

nn Audio section

• Power amplifier

 

Rated output:

Front:

 

75 W + 75 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)

 

120 W + 120 W (6 Ω, 1 kHz with 0.7 % T.H.D.)

 

Center:

 

75 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)

 

120 W (6 Ω, 1 kHz with 0.7 % T.H.D.)

 

Surround:

 

75 W + 75 W (8 Ω, 20 Hz – 20 kHz with 0.08 % T.H.D.)

 

120 W + 120 W (6 Ω, 1 kHz with 0.7 % T.H.D.)

Output connectors:

6 – 16 Ω

• Analog

 

Input sensitivity/Input impedance:

200 mV/47 kΩ

Frequency response:

10 Hz – 100 kHz — +1, –3 dB (DIRECT mode)

S/N:

98 dB (IHF–A weighted, DIRECT mode)

nn Video section

• Standard video connectors

 

Input/output level and impedance:

1 Vp-p, 75 Ω

Frequency response:

5 Hz – 10 MHz — +1, –3 dB

• Color component video connector

 

Input/output level and impedance:

Y (brightness) signal — 1 Vp-p, 75 Ω

 

PB / CB signal — 0.7 Vp-p, 75 Ω

 

PR / CR signal — 0.7 Vp-p, 75 Ω

Frequency response:

5 Hz – 60 MHz — +0, –3 dB

nn Tuner section

[FM]

[AM]

 

(Note: μV at 75 Ω, 0 dBf = 1 x 10–15W)

 

Receiving Range:

87.5 MHz – 107.9 MHz

520 kHz – 1710 kHz

Usable Sensitivity:

1.2 μV (12.8 dBf)

18 μV

50 dB Quieting Sensitivity:

MONO 2.8 μV (20.2 dBf)

 

S/N (IHF-A):

MONO 70 dB

 

 

STEREO 67 dB

 

Total harmonic Distortion (at 1 kHz):

MONO 0.7 %

 

nn General

STEREO 1.0 %

 

 

 

Power supply:

AC 120 V, 60 Hz

 

Power consumption:

360 W

 

 

0.1 W (Standby)

 

 

3 W (CEC standby)

 

Maximum external dimensions:

434 (W) x 171 (H) x 381 (D) mm (17-3/32” x 6-47/64” x 15”)

Weight:

9.2 kg (20 lbs 4.5 oz)

 

nn Remote Control Unit (RC-1147)

 

 

Batteries:

R6/AA Type (two batteries)

 

Maximum external dimensions:

53 (W) x 224 (H) x 28 (D) mm (2-3/32” x 8-13/16” x 1-7/64”)

Weight:

160 g (5.6 oz, including batteries)

 

For purposes of improvement, specifications and design are subject to change without notice.

70