ENGLISH

Playback in ZONE2 (Separate room)

Simple

•You can operate this unit so as to enjoy audio in a room (ZONE2) other than the MAIN ZONE (room where the unit is located).

•You can simultaneously play back the same source in both the MAIN ZONE and ZONE2. You can also play back separate sources in the MAIN ZONE and ZONE2.

Audio output

ZONE2 playback by speaker output

The ZONE2 audio signals are output from this unit’s SURR. BACK/ AMP ASSIGN speaker terminals using the amplifier assignment function.

nnConnecting and setting the speakers

“Amp Assign” setting

 

(vpage 52) and audio

Connecting the speakers

signals output

 

Playback

1 Switch ZONE SELECT to “ZONE2”. The remote control unit switches to the operating mode for ZONE2.

2 Press AMP.3 Press ZONE/DEVICE ON to turn on the ZONE2 power.

The indicator on the display lights.

•Also press input source select button when in standby mode, the power turns on.

•When ZONE/DEVICE OFF is pressed, ZONE2 turns off.

•Power in ZONE2 can be turned on or off by pressing ZONE2 ON/OFF on the main unit.

Input source select buttons

Adjust the volume

Use VOL df to adjust the volume.

GAdjustable rangeH – – – –80dB – –40dB – 18dB

(When the “Volume Display” (vpage 57) setting is “Relative”)

GAdjustable rangeH

0 – 41 – 99

(When the “Volume Display” (vpage 57) setting is “Absolute”)

•At time of purchase, “Volume Limit” (vpage 56) is set to “–10dB (71)”.

Turn MASTER VOLUME after pressing ZONE2 SELECT on the main unit to adjust the sound volume.

Turning off the sound temporarily

Press MUTE.

The sound is reduced to the level set at “Mute Level” (vpage 56) in the menu.

• To cancel, either adjust the volume or press MUTE again.

version

version Basic

MAIN ZONE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

This unit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ZONE2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Output signal :

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ZONE2

 

 

 

 

 

 

 

 

 

 

 

Stereo (L / R)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4 Press the input source select button. The audio signal of the selected source is output to ZONE2.

•Turn SOURCE SELECT after pressing ZONE2 SELECT on

the main unit to select an input source.

When power for both MAIN ZONE and ZONE2 is set to ON, power of

the MAIN ZONE only can be turned off. Select “MAIN” in step 1 then press ZONE/DEVICE OFF.

• The setting is canceled when the zone’s power is turned off.

version Advanced

We recommend using high quality pin-plug cables for audio connections in order to prevent noise.

NOTE

It is not possible to play the digital audio signals input from the HDMI, COAXIAL or OPTICAL connectors in ZONE2.

Information

37