Denon AVR-890 Making the ZONE2 settings (ZONE2 Setup), Yes, LFE, 0dB, SW :, No :, Last, Full, Basic, Large, OFF :, OFF :, • Used, Front :, Small :, / 250Hz, –40dB :, –20dB :

ENGLISH

Getting
	Setting items	Setting contents
Started
	2CH DIRECT/STEREO	Setting : Select the method for setting the speakers used in the 2-channel
	Make speaker settings for 2- direct and stereo playback modes.
Connections	channel mode playback.	• Basic : The settings at “Speaker Setup” (vpage 27) are applied.
		• Custom : Make separate settings for 2-channel mode.
		Front : Set the front speaker size.
		• Large : Use of a large speaker that can adequately play back low
		frequencies.
		• Small : Use of a small speaker that has inadequate playback capacity
Settings
		• Yes : Use a subwoofer.
		for low frequencies.
		SW : Set the presence of a subwoofer.
		• No : Select when a subwoofer is not connected.
Playback
		SW Mode : Select low range signal to be reproduced by subwoofer.
		• LFE : Add the low frequency signal of the channel for which the speaker
		size is set to “Small” to the subwoofer signal and output it.
-Multi		• LFE+Main : Add the low frequency signal of all channels to the
		subwoofer signal and output it.
Zone		Crossover : Outputs at below set frequency, each speaker’s bass signal
		output from the subwoofer.
Remote		• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz
		/ 250Hz
		Distance FL / Distance FR : Select the speaker you want to set, and set
Control		the CH Level. Set the value that is closest to the measured distance.
		CH Level FL/ CH Level FL FR : Select the speaker you want to set, and
		• 0.0ft ~ 60.0ft (12.0ft) / 0.00m ~ 18.00m (3.6m)
Information		set the CH Level. Adjust the level of each channel.
		• –12.0dB ~ +12.0dB(0.0dB)
	Auto Surround Mode	ON : Memorize settings. Most recently stored surround mode is
	Make setting for memorizing	automatically selected.
	surround mode setting for OFF : Do not memorize settings. Surround mode does not change
Troubleshooting	each input signal type.	according to input signal.
		The auto surround mode function lets you store in the memory the
		surround mode last used for playing the four types of input signals
		listed below.
		q Analog and PCM 2-channel signals
Specifications		w Dolby Digital and DTS 2-channel signals

e Dolby Digital and DTS multi-channel signals

r Multi-channel signals other than Dolby Digital and DTS (PCM, etc.)

NOTE

When playing in the PURE DIRECT mode, the surround mode does not change even if the input signal is changed.

Making detailed settings (Manual Setup)

Setting items		Setting contents
EQ Customize		Audyssey Byp. L/R / Audyssey Flat / Manual
Set so that unused equalizer		• Used
settings	are not displayed	• Not Used
when	is used.	NOTE

•Set so that “Audyssey Byp. L/R” and “Audyssey Flat” settings can be made when Audyssey™ Auto Setup is performed.

•Equalizer settings for which “Not Used” is set with the Quick Select function cannot be stored and called out.

Making the ZONE2 settings (ZONE2 Setup)

Default settings are underlined.

Make settings for audio playback in a ZONE2 system.“ZONE2 Setup” is displayed when ZONE2 is selected with “Amp Assign” (vpage 27).

	Setting items			Setting contents
Level Lch				–12dB ~ +12dB (0dB)
Adjust the left channel output
level.
Level Rch				–12dB ~ +12dB (0dB)
Adjust	the	right	channel
output level.
Volume Display				Relative : The volume is displayed within the range of – – –dB (Minimum),
Set the ZONE2			volume	–80 dB ~ +18 dB.
display method.				Absolute : The volume is displayed within the range of 0, 1 ~ 99.
Vol.Limit				OFF : Do not set a maximum volume.
Make a setting for maximum				–20dB(61) / –10dB(71) / 0dB(81)
volume.
Power On Level				Last : Use the memorized setting from the last session.
Define	the	volume	setting	– – – : Always use the muting on condition when power is turned on.
that is active when the power				–80dB(1) ~ +18dB(99) : The volume is adjusted to the set level.
is turned on.
Mute Level				Full : The sound is cut off entirely.
Set the amount of attenuation				–40dB :The sound is attenuated by 40 dB.
when muting is on.				–20dB :The sound is attenuated by 20 dB.

•The volume is displayed using the display method set at “Volume Display” (vpage 31).

•Set the main volume at “Volume Control” (vpage 32).

	Remote control
		:	Displaying the menu	: Moves the cursor (Up/Down/Left/Right)	: Decision the setting	: Return to previous menu
	operation buttons		Cancel the menu